Skip to content
Gas furnace and water heater in a home basement
Brands we repair

Rheem furnace repair in Toronto

(647) 692-0819Open 24/7, day or night

Rheem furnace repair covers everything from a basic single-stage unit to a connected, modulating one, and the right first step differs between them. Below you will find who makes Rheem, how its furnace series are laid out, the repairs we see most and what you can check yourself. Our general furnace repair in Toronto page covers the wider service, and Vaughan homes are covered too.

Request a technician

Tell us what’s going on. We’ll call to confirm a time.

What do you need?
How soon? Optional
Add email, details or text updatesOptional

Or call (647) 692-0819Used only to book your visit. Privacy

Key takeaways

  • We repair Rheem gas furnaces across Toronto, North York, Vaughan and the GTA.
  • Rheem describes EcoNet as its connectivity feature, found on some models.
  • Start with the thermostat, filter, breaker and furnace door before calling.
  • Gas smell: outside, then Enbridge. CO alarm: everyone out, then 911.
  • Open 24/7, with a flat-rate price you approve before work begins.

Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.

On this page
  1. Rheem furnace repair across Toronto and the GTA
  2. Rheem in brief: the maker and its sister brands
  3. How Rheem’s furnace series are laid out
  4. What EcoNet means when a Rheem furnace stops heating
  5. Common Rheem furnace repairs
  6. What to check yourself first
  7. Finding the model number and reading the status light
  8. Rheem furnace error codes on the R96T display
  9. When to repair a Rheem furnace and when to replace it
  10. Rheem warranty and registration
  11. Safety, and what a Rheem furnace repair visit involves
  12. Rheem furnace repair questions

Rheem furnace repair across Toronto and the GTA

We repair Rheem gas furnaces in Toronto, North York, Vaughan, Markham and the surrounding GTA. A TSSA-certified gas technician handles the work, and we give you a flat-rate price before touching anything. When the heat is out at night or on a weekend, call. Technicians go out day or night.

Rheem in brief: the maker and its sister brands

Rheem is an independent subsidiary of Paloma Industries, which bought Rheem’s then parent, Pace Industries, in 1988. Rheem sells in Canada, and Ruud, Friedrich, WeatherKing and Sure Comfort are heating and cooling brands alongside it.

Ruud is one of those sister brands. We do not assume a Rheem and a Ruud furnace share parts, so each repair starts from the label on the unit in front of us.

How Rheem’s furnace series are laid out

Rheem’s US furnace page groups its gas furnaces into three series, and the series tells a technician how much control electronics to expect. The figures below are Rheem’s, from a US site, so the lines on sale in Canada may differ and we confirm yours on site.

Rheem furnace series as described on Rheem’s US furnace page
SeriesEfficiency and staging statedNotable feature stated
Prestige97% and 98% AFUE, modulatingEcoNet enabled, constant CFM motor
Classic PlusTwo-stage, up to 97% AFUEConstant torque ECM on one model
ClassicSingle-stage, 92% to 95% AFUESimplest controls of the three

What EcoNet means when a Rheem furnace stops heating

Rheem describes EcoNet as its connectivity feature, shown as “EcoNet Enabled” on most Endeavor line models. If yours is one of them, a no-heat call can be a communication or thermostat problem as easily as a burner problem.

Tell us whether the thermostat screen is lit, and whether the Wi-Fi or app still responds. That narrows the search before we arrive. A furnace that heats fine but will not talk to its thermostat is a different job from one that never lights, and we price them as the separate faults they are.

Common Rheem furnace repairs

Gas furnaces tend to fail in the same handful of places whatever the name on the cabinet. What we replace on yours depends on its series and age, and we confirm that once we see the unit.

  • Flame sensor cleaning for a burner that lights and then drops out.
  • Igniter replacement when the furnace tries to start and never lights.
  • Inducer motor and pressure switch faults that stop the start-up sequence.
  • Limit switch trips caused by dirty filters or blocked returns.
  • Blower and ECM motor repairs, including constant-torque and constant-CFM types.
  • Control board replacement, plus condensate trap and drain cleaning.

What to check yourself first

The simplest causes of a cold house are often outside the furnace itself, so these checks come before any service call. Work through them in order, and stop at once if you smell gas or feel unsure about anything.

  • Make sure the thermostat is on Heat and has power or fresh batteries.
  • Check that the furnace switch is on and the breaker has not tripped.
  • Swap a dirty filter and close the furnace door firmly.
  • Clear outdoor intake and exhaust pipes of snow, by hand only.
  • Try one reset, and leave it alone if the problem returns.

Finding the model number and reading the status light

The model and serial label on your furnace identifies it, and the owner’s manual shows where the label sits. We cannot say where Rheem places its plate. For an R96T, the codes are in the next section; for other models, we read the display against that model’s own documentation. Knowing the series, such as Prestige or Classic, helps us plan the visit.

If the display blinks, photograph it or record a short video. Please do not take covers off to look for a label, because there are live parts and gas controls behind them.

Rheem furnace error codes on the R96T display

The Rheem R96T shows its status on a seven-segment display on the furnace control. It reads 0 in standby, a lower-case h for low-stage gas heat and a capital H for high stage. A fault code has two digits shown one after the other, so code 22 appears as a 2 followed by another 2, and two codes can alternate, such as 10 and 11.

These meanings come from Rheem’s R96T installation instructions (opens in a new tab), form 92-24161-157, Rev. 4, December 2017, which cover the two-stage (-)96T series. Other Rheem models may use different codes. Treat a code as the place testing starts.

Fault codes in Rheem’s R96T installation instructions
CodeWhat it meansWhat to do
10One-hour lockout, shown alternating with the code that caused itBook a repair if it repeats
11Failed ignition; four failures in a row bring a one-hour lockoutBook a repair
12Weak flame sense signal, though the furnace keeps heatingBook a repair
13Flame was lost after it had been establishedBook a repair
14Flame present while the gas valve is offCall a technician right away
22Main limit open; no gas heat until the limit cools and closesCheck the filter, then call a technician
33Manual reset rollout limit open; Rheem says flames rolled out of the normal areaCall a technician
44Low pressure switch closed while the inducer is offCall a technician
45Low pressure switch open with the inducer on high speedBook a repair
57High pressure switch open with the inducer on high speedBook a repair
59Water sensed in the collector box, often from a blocked condensate drain or trapBook a repair
61The blower motor cannot runBook a repair
93Internal fault on the furnace controlBook a repair

Jot down every code the display cycles through, since a lockout code like 10 usually appears beside the fault behind it. Our TSSA-certified gas technicians read the display on site and test the part a code points to before anything is replaced. Rheem also asks owners to keep the air filters clean.

When to repair a Rheem furnace and when to replace it

A gas furnace typically lasts 15 to 20 years, so a failed part on a furnace in its first decade is almost always worth fixing. Past 15 years, we weigh the repair against how many parts are wearing out and how much heat the furnace still delivers.

Repair and replacement guide by furnace age
AgeOne failed partSeveral faults or a safety problem
Under 10 yearsRepairRepair, then investigate the cause
10 to 15 yearsRepairPrice both options
15 to 20 yearsUsually repairReplacement likely makes sense
Over 20 yearsCase by caseReplace

Rheem warranty and registration

Warranty terms and registration rules are set by the maker, and we cannot state them for Rheem. Check Rheem’s Canadian warranty page, keep your installation papers and hold on to every service receipt. If you are unsure whether your furnace was registered, that page is the place to ask.

Many warranties ask for proof of regular maintenance, which our maintenance plan provides. We do not do warranty work on Rheem’s behalf.

Safety, and what a Rheem furnace repair visit involves

If you smell gas, leave the house and call Enbridge Gas at 1-866-763-5427 from outside. If a carbon monoxide alarm goes off, get everyone out and call 911. The Enbridge Gas safety page (opens in a new tab) has more guidance.

On a booked visit you get a two-hour arrival window and a text. We test the furnace, explain the fault and quote a flat rate. Richmond Hill and Mississauga homes are covered as well, and nothing is repaired until you agree. If the visit shows the furnace is near the end of its life, we say so plainly and let you decide what comes next.

Assurance HVAC Heating & Cooling is an independent HVAC contractor, not affiliated with or authorized by Rheem. Brand names are trademarks of their owners.

FAQ

Rheem furnace repair questions

Can you repair my Rheem furnace in Toronto?

Yes. Our technicians work on Rheem gas furnaces across Toronto and the GTA, including connected EcoNet models and simpler single-stage ones. We are an independent contractor and you approve a flat-rate price before we start. Call any hour, because we are open 24/7 for no-heat emergencies.

What is EcoNet on a Rheem furnace?

Rheem describes EcoNet as its connectivity feature, and its US furnace page marks most Endeavor line models as EcoNet Enabled. If your furnace has it, tell us which thermostat or app you use and how it is behaving when you call. A wiring, power or settings fault can look like a furnace problem.

Is a Ruud furnace the same as a Rheem?

Ruud is a Rheem brand, so they are sister brands. We do not claim they share parts, factories or diagnostics, because we have no source for that. We repair each furnace from its own model label and documentation, whichever name is on the cabinet.

Why does my Rheem furnace start and then stop?

A furnace that lights and quits is usually shutting itself down for a reason. A coated flame sensor, restricted airflow from a dirty filter, or blocked vent pipes are the usual suspects. Replace the filter and clear any snow from outdoor pipes. If it persists, book a technician.

How do I know if my Rheem furnace is modulating?

Check the model label or the paperwork from installation. Rheem’s US page lists its Prestige series as modulating, while the Classic Plus is two-stage and the Classic is single-stage. We cannot confirm Canadian lines from that page, so we read the label on your unit.

What does a Rheem furnace error code mean?

It points to the safety or part the control flagged. On the R96T, Rheem’s manual lists 13 as flame lost after lighting and 22 as the main limit open, while a 10 alternating with another code means a one-hour lockout. Check the filter, try one reset at most, and call us if the code returns.

Should I replace my Rheem furnace or repair it?

Age and fault decide it. Gas furnaces typically last 15 to 20 years, so one failed part on a younger unit is usually worth repairing. A cracked heat exchanger or a string of failures on an older one points to replacement. We explain both before you commit to anything.

Book a visit

Need Rheem furnace repair? We’ll call you back to book.

Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.

(647) 692-0819

Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies

Request a technician

Tell us what’s going on. We’ll call to confirm a time.

What do you need?
How soon? Optional
Add an email or detailsOptional

Or call (647) 692-0819Used only to book your visit. Privacy