
Armstrong Air lists gas furnaces from 80% up to 98% AFUE, and the efficiency level of yours changes how it vents, drains and fails. We handle Armstrong Air furnace repair across Toronto and the GTA, and you approve a flat-rate price before work begins. Our general furnace repair in Toronto page covers the wider service.
Key takeaways
- Armstrong Air lists furnaces from 80% to 98% AFUE, and the type decides what usually fails.
- Higher-efficiency models drain condensate and vent through plastic pipe, so clogs and ice matter.
- We service all major brands, and our technicians work on Armstrong Air furnaces.
- Gas smell: go outside, then call Enbridge Gas. CO alarm: everyone out, call 911.
- You approve a flat-rate price first, and we are open 24/7.
Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.
On this page
- Armstrong Air furnace repair for Toronto homes
- Armstrong Air and its Lennox connection
- Reading the Armstrong Air efficiency range
- Why the efficiency level changes the repair
- Typical Armstrong Air furnace problems
- Finding your model and age before you call
- Armstrong Air furnace error codes, from E200 to E290
- Armstrong Air furnace repair or replace?
- Warranty and registration
- Gas and carbon monoxide safety with an older furnace
- Booking a repair across the GTA
- Armstrong Air furnace repair questions
Armstrong Air furnace repair for Toronto homes
We repair Armstrong Air gas furnaces in Toronto and across the GTA, whether the furnace will not light, shuts off mid-cycle or runs without warming the house. Gas work is done by TSSA-certified technicians. We are an independent contractor and service all major brands.
Armstrong Air and its Lennox connection
Armstrong Air’s site footer credits Allied Air Enterprises LLC, a Lennox International company, and Armstrong Air and Allied Air are both among Lennox’s Home Comfort brands. So Armstrong Air is a Lennox sister brand.
Being sister brands does not tell us that any part fits both, and we do not assume it. We read the label on your unit and work from that. The maker describes itself as “The Professional’s Choice” and says it was founded in 1928.
Reading the Armstrong Air efficiency range
Armstrong Air’s site lists gas furnaces from 80% to 98% AFUE. AFUE is the share of fuel turned into heat, so a 96% furnace sends about 96 cents of each fuel dollar into your home. The maker’s ladder covers modulating, two-stage and single-stage designs.
| Type listed | Stated AFUE | Notes from the maker |
|---|---|---|
| Modulating, variable-speed blower | 98% | Top of the range |
| Variable-speed | 97% | Variable-speed blower |
| Two-stage, constant torque motor | 97% | Two-stage heating |
| Single-stage | 96% and 93% | Single-stage gas valve |
| 80% models | 80% | Models A802VK, A802EK and A801EK |
Armstrong Air also uses the names Pro Series and Protection Pro on some models, and says its VK models are MyHomeComfort enabled. The maker cites a patented EHX heat exchanger technology without giving detail, so we do not describe how it works. See the maker’s gas furnace page (opens in a new tab) for its own wording.
Why the efficiency level changes the repair
A furnace in the 90% range or higher is a condensing design, and that brings extra parts that an 80% furnace does not have. Knowing which kind you own tells us where to look first.
80% furnaces
These vent hot exhaust up a chimney or metal flue. Common faults are a worn igniter, a coated flame sensor and a draft or pressure switch problem. Rust, soot or a blocked flue are things we look for, since they point to venting trouble.
Condensing furnaces, 90% and up
These pull heat from the exhaust until it turns to water, so they have a condensate trap and drain, plus plastic intake and exhaust pipes. A blocked drain or an iced vent end can shut the furnace down. On these models a no-heat call is sometimes a drain or venting fault rather than a failed burner.
Typical Armstrong Air furnace problems
Most calls come down to one of a handful of parts. Here is what each symptom commonly points toward, using the part names a technician will use when they diagnose your furnace on site.
- Furnace tries to light and fails: hot surface igniter, flame sensor or gas valve.
- Lights, runs briefly, then stops: dirty flame sensor, limit switch or restricted airflow.
- Inducer fan runs but nothing follows: pressure switch, blocked vent or condensate trap.
- Blower runs constantly or not at all: blower motor, ECM motor or control board.
- Puddle under a condensing furnace: condensate trap, drain line or pump.
- Cold rooms with the furnace running: filter, ductwork or a failing blower.
Finding your model and age before you call
Armstrong Air model names follow a pattern, such as A98MVK for the modulating 98% unit and A961EK for a single-stage 96% one. The rating plate on your furnace shows the exact model, and we cannot tell you from the name alone how old the unit is.
Take a photo of the plate and of any code on the display. For the A961EK, the common codes are listed in the next section. For any other model, the technician reads the code on site against that unit’s own manual.
Armstrong Air furnace error codes, from E200 to E290
Current Armstrong Air furnaces such as the A961EK show faults on a seven-segment display on the ignition control, next to a push button that brings back the 10 most recent codes. A decimal point blinking once a second means the furnace is idle, and an H means gas heat. A code names the circuit to check, not the part that broke.
The list comes from Armstrong Air’s A961EK installation instructions (opens in a new tab), form 508618-01, which cover the A96UH1EK upflow and horizontal furnace. Other Armstrong Air models can use different codes, so check the label on yours.
| Code | What it means | What to do |
|---|---|---|
| E200 | Rollout switch circuit is open now or tripped before, causing a hard lockout | Call a technician |
| E223 | Pressure switch did not close (stuck open) | Clear snow or ice from the outdoor vent pipes by hand; if it stays, book a repair |
| E224 | Pressure switch did not open (stuck closed) | Book a repair |
| E227 | Pressure switch opened during the trial for ignition or while the burner was on | Book a repair |
| E240 | Flame current is low while the furnace is heating | Book a repair |
| E241 | The control still sees flame when there should be none | Call a technician now |
| E250 | Primary limit switch opened | Call a technician |
| E270 | 60-minute soft lockout: no flame was sensed after the maximum number of retries | Book a repair |
| E271 | 60-minute soft lockout; the last retry failed when the pressure switch opened | Check the vent pipes for snow, then book a repair |
| E273 | Soft lockout after the flame kept dropping out during heating | Book a repair |
| E274 | Soft lockout because the limit kept opening or stayed open past 3 minutes | Call a technician |
| E290 | Igniter circuit fault: a failed igniter or the circuit that powers it | Book a repair |
Note the code and what you heard or saw just before it appeared. One of our TSSA-certified gas technicians reads the stored codes, tests the part each one points to and only then quotes the repair. The filters on these furnaces sit outside the cabinet, and the maker’s manual says to inspect them monthly.
Armstrong Air furnace repair or replace?
Gas furnaces typically last 15 to 20 years, and an 80% model of that age is often a better candidate for replacement than for another repair. Newer Armstrong Air furnaces usually justify the fix.
| Your furnace | Often better to | Reason |
|---|---|---|
| Condensing, under 10 years, one fault | Repair | Most parts still have service life |
| 80% model past 15 years | Price a replacement | Higher fuel use and aging parts |
| Cracked heat exchanger | Replace | Not a safe repair |
| Repeated drain or vent faults | Fix the cause, then reassess | Install issues can repeat |
Our repair or replace guide shows how we weigh these.
Warranty and registration
Armstrong Air’s site links a Canadian Rebate Search, but its listed address and phone are in the US. For warranty terms that apply in Ontario, check the maker’s Canadian information and your install paperwork, and keep your serial number with your invoice.
Our own repairs carry a written workmanship warranty. If you’re weighing a cold-climate heat pump alongside the furnace, see our rebates page.
Gas and carbon monoxide safety with an older furnace
A gas smell means you leave the home first and phone Enbridge Gas at 1-866-763-5427 after you are outside. A carbon monoxide alarm that sounds means everyone gets out and someone dials 911.
Older non-condensing furnaces rely on a clear flue, so soot, rust streaks or a smell of exhaust near the unit deserve a call, not a wait.
Booking a repair across the GTA
Booked visits come with a text and a two-hour arrival window. If you have no heat in the middle of the night, our line is answered 24/7 and a technician can come out at any hour, with emergency calls first in line.
We serve Toronto, North York, Richmond Hill, Vaughan, Markham, Mississauga and Oakville. In Markham, start with our furnace repair in Markham page for local detail.
Assurance HVAC Heating & Cooling is an independent HVAC contractor, not affiliated with or authorized by Armstrong Air. Brand names are trademarks of their owners.
Armstrong Air furnace repair questions
What does an Armstrong Air furnace error code mean?
It names the part or circuit that tripped. On the A961EK, Armstrong Air’s manual lists E223 as the pressure switch staying open and E250 as the primary limit switch opening, and the table above shows more. Clear snow from the outdoor vent pipes and check the filter, then call us if the code returns.
Who makes Armstrong Air furnaces?
Armstrong Air’s site credits Allied Air Enterprises LLC, a Lennox International company. Armstrong Air is among Lennox’s Home Comfort brands. We do not claim the two brands share parts or factories. We check your unit’s own label before ordering anything.
What AFUE do Armstrong Air furnaces have?
The maker lists gas furnaces from 80% to 98% AFUE, including 80%, 93%, 96%, 97% and 98% models. Your own furnace’s rating is on its label. A higher AFUE means a condensing design with plastic venting and a drain, which affects what we check.
Why is my Armstrong Air furnace running but not heating?
The burner may be failing to stay lit, often from a worn igniter or coated flame sensor, or a safety switch may be shutting it down. Check the filter and thermostat, then call us. Please do not keep resetting it, since repeated lockouts point to a real fault.
Is water under my Armstrong Air furnace normal?
A condensing furnace makes water that should leave through the drain, so a puddle means a blocked trap, a cracked drain line or a failed pump. An 80% furnace should not produce much water. Either way, switch the furnace off if water is spreading and call us.
Should I repair or replace an old 80% Armstrong Air furnace?
If it is past 15 years and needs more than a small part, price a replacement alongside the repair. A newer condensing model can cut fuel use. We give you the flat-rate repair price first so you can compare, with no pressure to choose either way.
Do you offer Armstrong Air furnace repair at night?
Yes. We are open 24/7 for no-heat emergencies, and technicians go out day or night, weekends included. Emergency calls are handled first. You approve the flat-rate price before the technician starts any work, so there are no surprises on the invoice.
Are you affiliated with Armstrong Air?
No. We are an independent contractor and service all major brands. Our technicians work on Armstrong Air furnaces, but we have no link to the maker and do not perform warranty work for it. Check your own paperwork for what the maker covers.
Need Armstrong Air furnace repair? We’ll call you back to book.
Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.
Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies
