Skip to content
Gas furnace and water heater in a home basement
Assurance HVAC Heating & Cooling of Mississauga

Furnace repair in Mississauga homes

(647) 492-6590Open 24/7, day or night

Assurance HVAC Heating & Cooling of Mississauga handles furnace repair in Mississauga in houses of every age and size, from 1960s bungalows in Applewood to townhomes in Churchill Meadows and custom builds in Lorne Park. A TSSA-certified gas technician tests the furnace one stage at a time, shows you what failed and gives you a flat-rate price before touching anything. As a licensed HVAC contractor in Mississauga, we fix all major brands, standard and high-efficiency, and stand behind each repair with a written workmanship warranty.

Request a technician

Tell us what’s going on. We’ll call to confirm a time.

What do you need?
How soon? Optional
Add email, details or text updatesOptional

Or call (647) 492-6590Used only to book your visit. Privacy

Key takeaways

  • Gas furnace repair across Mississauga, from Port Credit to Meadowvale, on all major brands.
  • Every gas repair is done by a TSSA-certified technician with WSIB coverage and insurance.
  • You see a flat-rate price after the diagnosis and approve it before work begins.
  • Booked repairs come with a two-hour arrival window and a heads-up text.
  • No-heat calls are picked up 24/7, and every repair carries a written workmanship warranty.

Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling of Mississauga service team.

On this page
  1. Signs you need furnace repair in Mississauga
  2. Furnace not heating? Five checks before you book
  3. Common furnace repairs in Mississauga, part by part
  4. Why furnaces overheat in older Mississauga homes
  5. High-efficiency furnace repair in Mississauga townhomes
  6. Repairing zoned and modulating furnaces near the lake
  7. How furnace repair in Mississauga works, step by step
  8. Repair or replace a furnace in a Mississauga home?
  9. What affects furnace repair cost in Mississauga?
  10. Furnace brands we repair across Mississauga
  11. Gas smell or CO alarm: safety comes before repair
  12. No heat in a Mississauga home: calls answered 24/7
  13. Keeping a Mississauga furnace out of the repair queue
  14. Furnace repair questions from Mississauga homeowners

Signs you need furnace repair in Mississauga

Book a repair when the house stops warming up, the furnace starts and stops every few minutes, or it makes a sound it never made before. In a Mississauga split-level the first clue is often the lowest floor falling further behind than usual, because that level was already the hardest one to heat.

  • No heat at all, or a furnace blowing cold air through the registers
  • Burners that catch, then go out again within a few seconds
  • Short cycling, where the furnace runs in brief bursts all day
  • A squeal, rattle or steady hum from the blower or inducer motor
  • Water under a high-efficiency furnace, or a burner flame that has turned yellow

Furnace not heating? Five checks before you book

When the furnace is not heating, spend a few minutes on the simple causes first. A thermostat on the wrong mode, a switched-off breaker or service switch, a loose blower door, a clogged filter or a blocked condensate line can each stop a furnace, and all five are safe for a homeowner to look at.

  • Thermostat: on Heat and set two or three degrees warmer than the room, with new batteries if the display is blank
  • Power: the furnace breaker and the light-style service switch beside the furnace both on
  • Blower door: look, don’t open it. The furnace won’t start if the door isn’t fully seated, so mention a loose one when you book
  • Filter: replaced if you can’t see light through it
  • Condensate: look for a kinked drain hose or a condensate pump that’s full or unplugged, and tell us what you see

Still nothing? If the status light shows through the window in the furnace door, note its blink pattern, then book a visit.

Common furnace repairs in Mississauga, part by part

Most furnace repair in Mississauga comes down to a short list of furnace parts that wear with use: the ones that light the burners, prove the flame, clear combustion gases, guard against overheating and push warm air through the house. We test them in the order the furnace calls on them, so we replace the part that actually failed.

The furnace parts that fail most often, and what you notice
PartIts jobWhat you notice when it fails
Hot surface igniterHeats up to light the gasInducer runs, burners never light
Flame sensorProves the burners are litFlame for a few seconds, then shutdown
Inducer motorPulls exhaust through the ventWhine or rattle at start-up, then lockout
Pressure switchConfirms the vent draws before ignitionBlinking code and no flame, often after snow
Limit switchStops the burners when the furnace overheatsHeat comes in spurts, fan stays on
Blower motor or ECM modulePushes warm air into the ductsBurners on, barely any air at the registers
Control boardSequences each step and stores error codesIgnores the thermostat or quits at random
Condensate trap and drainDrains water from a condensing furnaceWet floor, gurgling, pressure switch code

Igniters, flame sensors, capacitors and pressure switches travel with the technician, so most of these jobs are finished on the first visit.

Why furnaces overheat in older Mississauga homes

In Applewood, Cooksville, Malton and Erindale, many houses from the 1950s to the 80s now run a second or third furnace on the ductwork they were built with. When the returns can’t feed the blower enough air, the heat exchanger runs hot, the limit switch trips and the furnace shuts off early, again and again.

A limit switch that keeps tripping is a symptom, not the fault. We measure temperature rise and static pressure, then fix the cause: a clogged filter, a closed damper, a crushed run or too few returns.

In Erin Mills and Meadowvale splits, closing upstairs registers to push heat down starves the furnace of air, so reopening them and balancing dampers is often part of the fix.

High-efficiency furnace repair in Mississauga townhomes

Townhomes and semis in Churchill Meadows and Lisgar, built mostly from the 1990s on, tend to have compact mechanical rooms. When the furnace in one of those rooms is a condensing model, the repair usually involves water or venting: a sludged condensate trap, a drain pump that stopped, or plastic vent pipes blocked outside.

Condensate trap, hose and pump

A condensing furnace makes water whenever it runs, and where no floor drain is close, a small pump lifts it away. When the trap clogs or the pump’s float sticks, water backs up and the pressure switch shuts the furnace down. We clean the trap, flush the hose and test the pump.

Vent pipes on a back or side wall

Townhome vent pipes may leave through the back wall or beside the garage, where snow drifts. A blocked intake or exhaust trips the pressure switch, and a pipe sagging indoors can hold water and set off the same code. We clear the ends, check the slope and secure the pipe.

Repairing zoned and modulating furnaces near the lake

Along the lake in Port Credit, Mineola, Lorne Park and Clarkson, custom homes that replaced the original bungalows often have zoning or a second system. When the furnace is two-stage or modulating, a repair is more likely to involve electronics: an ECM blower module, a zone damper, a staging control or the board that ties them together.

With zoning, one cold floor may be a stuck damper or a dead zone thermostat, so we check the zone panel before blaming the furnace. A failed ECM module can sometimes be replaced without the whole motor.

How furnace repair in Mississauga works, step by step

Every visit follows the same order. You get a two-hour arrival window when we book and a text as the technician heads over. The furnace is tested until the fault is proven, then you get a flat-rate price. Nothing is repaired until you approve it, and the figure holds for the whole job.

  • Send the request form or call, with the brand, rough age and any error code.
  • We call back to set the window and tell you the diagnostic fee first.
  • The technician runs a full call for heat and tests each stage of the sequence.
  • On an older furnace, a replacement quote sits next to the repair price.
  • After the repair, we run several heating cycles and recheck the safety controls.

Ontario’s fuel safety regulator is the TSSA (opens in a new tab), and only our TSSA-certified G2 and G1 gas technicians work on the gas valve, the burners or the gas line.

Repair or replace a furnace in a Mississauga home?

Repair is the better spend when the furnace is under about 15 years old and one wear part has failed. Replacement deserves a look at 15 to 20 years when it needs a heat exchanger, board or blower motor, or a technician every winter.

How we weigh a repair against a replacement
What we look atPoints to repairPoints to replacement
Furnace ageUnder about 15 years15 to 20 years, or past it
The failed partIgniter, flame sensor, pressure switch or capacitorHeat exchanger, or a board or motor on an aging unit
BreakdownsThe first in several wintersA call every heating season
EfficiencyAlready a condensing furnaceA mid-efficiency unit venting into a chimney

Plenty of Mississauga homes are already on their second or third furnace, some with central air just as old, and then we price the pair together. When a new furnace is the better call, see how we handle furnace installation in Mississauga.

What affects furnace repair cost in Mississauga?

The price comes down to the part that failed, whether the technician carries it, the age and make of the furnace and how hard it is to reach. You hear the flat diagnostic fee before booking and approve the repair price before work starts.

What changes the price of a furnace repair
FactorHow it affects the price
The failed partCleaning a flame sensor is a small job; a control board, inducer or ECM motor is a bigger one.
Brand and ageSome makes use proprietary parts, and parts for older models can take longer to find.
AccessCompact townhome mechanical rooms and finished basements take more labour time.
Related faultsA limit switch that tripped on poor airflow may need a duct or filter fix as well.
Part on hand or orderedAn ordered part means a second trip, which we flag before you approve.

Furnace brands we repair across Mississauga

Our technicians work on all the major furnace makes in local homes: Carrier, Lennox, Goodman, Trane, Amana, York, Rheem, Daikin, Bryant, Napoleon and more. We also repair furnaces next door in Oakville and Etobicoke.

Gas smell or CO alarm: safety comes before repair

If a carbon monoxide alarm goes off, get everyone, pets included, outside and call 911. If you smell gas, leave without touching switches, lighting a flame or using a phone inside, and call Enbridge Gas at 1-866-763-5427 once you’re outdoors. Call us about the furnace once the home is safe.

A cracked heat exchanger keeps a furnace off until it’s fixed or replaced, because it can let carbon monoxide into the air the blower moves around the house. A gas leak or a blocked or spilling vent means the same: the furnace stays off until it’s safe. Ontario requires CO alarms in every home with a fuel-burning appliance, a fireplace or an attached garage, next to each sleeping area and, since January 1, 2026, on every storey, and the province’s carbon monoxide safety guide (opens in a new tab) covers the details.

No heat in a Mississauga home: calls answered 24/7

If the furnace quits in the evening or on a weekend, call anyway. We’re open 24/7, no-heat calls from anywhere in Mississauga go to the front of the line, ahead of tune-ups and quotes, and a technician comes out day or night. Our emergency furnace repair page covers what to do while you wait.

Keeping a Mississauga furnace out of the repair queue

Many repairs on this page start as problems a fall tune-up would catch: a flame sensor losing its signal, a blower wheel packed with dust from 1960s ductwork, or closed registers in a split-level making the furnace run hot. Sorting those out in September costs less than a January breakdown.

Book furnace maintenance in Mississauga once a year, or join our maintenance plan for a fall furnace tune-up, a spring AC tune-up and priority booking when the schedule fills.

FAQ

Furnace repair questions from Mississauga homeowners

Can you repair a furnace in a tight townhome mechanical room?

Yes. Townhomes and semis in Churchill Meadows and Lisgar often have compact mechanical rooms, and a tight space doesn’t stop a repair. It can add labour time, which is already in the flat price you approve. Clear storage away from the furnace before the visit.

Can old ductwork make a newer furnace break down?

It can. In 1960s and 70s Mississauga homes, a furnace pushing air through original ducts with too few returns runs hot, so the limit switch trips, the blower works harder and the heat exchanger takes extra stress. We measure static pressure and temperature rise on the repair visit, and if the ducts are the cause, we explain the fix before pricing it.

Do your technicians reach Streetsville and Malton for furnace repair?

Yes. We cover all of Mississauga, from Malton, Meadowvale and Streetsville in the north to Port Credit and Clarkson by the lake, plus nearby Oakville and Etobicoke. Booked repairs get a two-hour arrival window, and no-heat calls are answered 24/7.

Is it worth repairing a 20-year-old furnace?

Sometimes. When only a small part such as an igniter has failed and the heat exchanger checks out, fixing it can make sense for another winter or two. A board, inducer or blower motor on a furnace that age, or a third breakdown, usually tips it toward replacement. You see both prices together, with our honest pick.

Can most furnace repairs be finished in one visit?

Most can. Technicians handling furnace repair in Mississauga carry the parts that fail most often, such as igniters, flame sensors, capacitors and pressure switches, so the repair is usually done the same visit. Some control boards, ECM modules and inducer motors are made for one model and have to be ordered, and you’ll know that before you approve the price.

What should I tell you when I book a furnace repair?

Tell us what the furnace is doing, roughly how old it is, the brand, and the blink pattern if the status light shows through the door’s window. Mention what you’ve tried, such as a new filter or a reset, and whether it vents through plastic pipes. That helps the technician bring the right parts on the first trip.

Is there a charge just to diagnose the furnace?

Yes. A flat diagnostic fee covers finding the fault, and you hear the amount when you call, before anything is booked. After the diagnosis you get a separate flat-rate repair price. You can approve it or not, and once approved, it stays the same even if the work takes longer than expected.

Why does my furnace short cycle on mild days but not cold ones?

On a mild Mississauga day the house needs only a little heat, so an oversized single-stage furnace reaches the thermostat setting in minutes and shuts off. A dirty flame sensor or a clogged filter can cause short cycling in any weather. We check the flame signal, airflow and temperature rise, and if the furnace is oversized, we explain the options.

Book a visit

Need furnace repair in Mississauga? We’ll call you back to book.

Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.

(647) 492-6590

Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies

Request a technician

Tell us what’s going on. We’ll call to confirm a time.

What do you need?
How soon? Optional
Add an email or detailsOptional

Or call (647) 492-6590Used only to book your visit. Privacy