
A furnace tripping the breaker is the electrical system doing its job. The breaker opens when the circuit draws more current than it should, and the cause is usually a failing motor, a short in the wiring or a worn component, not a bad breaker. This guide explains the common causes, the one reset that is safe to try, and when to leave it off and book furnace repair.
Key takeaways
- A breaker trips to protect the wiring from too much current, so it points to a real fault.
- Reset a tripped furnace breaker once, unless you smell burning. If it trips again, leave it off.
- Failing blower or inducer motors, shorted parts and loose wiring are the common causes.
- Never take the cover off the electrical panel or open the furnace, and never fit a bigger breaker.
- A TSSA-certified gas technician finds the fault and gives a flat-rate price before any work.
Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.
On this page
- What furnace tripping the breaker means
- Furnace tripping the breaker: what to do first
- Furnace tripping the breaker right away or after a while
- A failing blower motor
- Inducer motor, ignitor and control board faults
- Wiring faults, loose connections and rodents
- Shared circuits, humidifiers and worn breakers
- What not to do when the breaker keeps tripping
- Furnace tripping the breaker: when it’s a safety problem
- What a technician does on a tripping breaker call
- Preventing electrical trouble with your furnace
- Furnace tripping the breaker: common questions
What furnace tripping the breaker means
A breaker is a safety device that opens when too much current flows through the circuit, either because something is overloaded or because there is a short. When a furnace trips it, one of its electrical parts is drawing more power than it should or a wire is touching something it shouldn’t.
That matters because the breaker protects the wiring in your walls from overheating. A repeated trip is a warning, not a nuisance, and the useful question isn’t how to stop it tripping but what is pulling the extra current.
Furnace tripping the breaker: what to do first
Reset the breaker once, carefully, and watch what happens. Set the thermostat to Off, flip the furnace service switch off, and push the breaker fully to Off before switching it back On. Then turn the service switch on and set the thermostat to Heat. If it holds and the furnace heats normally, note the time and watch it.
If it trips again, now or later, stop. A second trip means the fault is still there, and every reset sends current through the problem part again. Leave the breaker off, keep the furnace switched off and book a technician.
- Burning smell, smoke, scorch marks, or a breaker that is hot or buzzing: don’t reset it, leave it off and call.
- Thermostat to Off, then the furnace service switch to Off
- Breaker pushed fully to Off, then back to On, one time only
- Service switch On, thermostat to Heat, and listen as the furnace starts
- Trips again: leave the breaker off and book a technician
Furnace tripping the breaker right away or after a while
When the breaker trips tells you a lot. A breaker that trips the moment you switch it on points to a dead short, such as a seized motor or damaged wiring. One that holds for a few minutes or an hour, then trips as the furnace runs, points to a part that overheats and draws more current as it warms up.
| What you notice | Likely cause | Who fixes it |
|---|---|---|
| Trips the instant it is switched on | Short in wiring, a motor or a control part | Technician |
| Trips as the blower starts | Failing blower motor or capacitor | Technician |
| Trips as the furnace starts, before the burners light | Inducer motor or ignitor drawing too much current | Technician |
| Trips after running for a while | Overheating motor, loose connection or overloaded circuit | Technician |
| Trips only on very cold days | Motor strained by long run times | Technician |
| Breaker feels hot or smells burnt | Overheated breaker or wiring connection | Electrician or technician; leave it off |
A failing blower motor
The blower motor is the biggest electrical load in the furnace, and a failing one is a common cause of a tripped breaker. As bearings wear or the windings degrade, the motor draws more current to turn, and eventually it pulls enough to open the breaker.
Typical signs are a humming or squealing noise, a blower that starts slowly or not at all, a hot motor housing or a burnt smell. A weak capacitor, on motors that have one, makes the same current spike. A technician measures the motor’s current draw and replaces the motor or capacitor.
Inducer motor, ignitor and control board faults
Other electrical parts can also draw too much current. The inducer motor, which clears exhaust before the burners light, can wear in the same way as the blower. A shorted hot surface ignitor, a failing transformer or a damaged control board can each overload the circuit as the start-up sequence begins.
If the breaker trips just as the furnace starts to light, one of these is a likely cause. They sit inside sealed compartments, so they are a technician’s job, and replacing the wrong part wastes money. Testing each part’s current draw finds the real culprit.
Wiring faults, loose connections and rodents
Wires inside and around the furnace age too. Insulation can crack from heat, connections can loosen from the vibration of the blower, and in basements and crawl spaces mice and squirrels can chew through wiring. Moisture from a leaking condensate drain or humidifier can also cause a short.
A loose or corroded connection heats up, and a hot connection can scorch the wiring or the breaker itself. If you smell burning, see discolouration at the panel or find the breaker warm to the touch, switch the furnace off and call, and don’t take the cover off the electrical panel to look.
What not to do when the breaker keeps tripping
The wrong response can turn a repair into a fire. A tripping breaker is protecting your home, so don’t defeat it. Reset it once as described above, and do nothing that bypasses the protection or opens up electrical equipment.
- Don’t keep resetting it to see if it holds. Each reset sends current through the fault.
- Don’t hold the breaker on, tape it or force it.
- Don’t replace it with a larger breaker. The wiring is sized for the original.
- Don’t take the cover off the electrical panel, and don’t open the furnace doors or the blower and burner compartments.
- Don’t test wiring or parts yourself.
- Don’t run the furnace on an extension cord.
Furnace tripping the breaker: when it’s a safety problem
Most tripped breakers are a repair, not an emergency, but a few signs alongside one call for immediate action. A burning smell, smoke, sparks, a buzzing breaker or a scorched panel mean you should leave the furnace off. Since the furnace burns gas, the usual gas and carbon monoxide steps apply as well.
- Burning or electrical smell: switch the furnace off at the service switch and call.
- Smell gas? Walk out without touching switches or your phone, and phone Enbridge Gas on 1-866-763-5427 once you are outside.
- Carbon monoxide alarm going off: everyone leaves, pets too, then 911 is called from outside.
The Ontario Fire Code puts carbon monoxide alarms next to each sleeping area, and on every storey since January 1, 2026, in homes that have a fireplace, an attached garage or a fuel-burning appliance, and the province lists the rules on its carbon monoxide safety (opens in a new tab) page.
What a technician does on a tripping breaker call
A TSSA-certified gas technician finds which part is drawing the extra current. They look over the wiring and connections, measure the current draw of the blower and inducer motors, test the capacitor and ignitor and check the control board and transformer for shorts. They also check why it happened, such as moisture or rodent damage.
The repair is quoted at a flat rate for your approval first, and our written workmanship warranty covers it. With no heat in the meantime, call for emergency furnace repair, which runs around the clock.
Preventing electrical trouble with your furnace
Most motor and wiring failures give warning signs a tune-up catches. A fall furnace maintenance visit cleans the blower, checks the motors and capacitors, tightens connections and looks for damaged wiring. A clean filter keeps the blower from straining, and a dry, clean furnace area keeps moisture and pests away.
Members of our maintenance plan get a fall furnace visit and a spring AC visit, plus priority booking. If the furnace is old and the repairs are stacking up, our furnace installation page explains replacing it.
Furnace tripping the breaker: common questions
Why does my furnace keep tripping the breaker?
Something in the furnace is drawing too much current or shorting. The usual causes are a failing blower or inducer motor, a bad capacitor, a shorted ignitor or control part, or loose or damaged wiring. Reset the breaker once, unless you smell burning, and if it trips again, leave it off and call a technician.
Is it safe to keep resetting the furnace breaker?
No. One careful reset is reasonable, but repeated resets send current through whatever fault tripped it, which can overheat wiring or damage parts. If it trips a second time, leave the breaker off and the furnace switched off, and book a technician to find the cause.
Can a dirty filter make a furnace trip the breaker?
It can contribute. A clogged filter makes the blower work against a restriction and run hotter, which strains a motor that is already worn. Replace the filter, but if the breaker trips again, the motor or wiring is the real problem and needs a technician.
Could the breaker itself be bad?
Sometimes, particularly an old one that trips below its rating, but it is not the first thing to suspect. A technician checks the furnace’s parts and wiring first. If they are healthy and the breaker still trips, an electrician should test and replace it. Never install a bigger breaker.
Why does my furnace trip the breaker only in very cold weather?
In a deep freeze the furnace runs far longer, so motors run hot and a worn blower or inducer motor draws more current. A frozen vent or a condensate problem can add strain too. Because it points to a weak part, have it checked before the next cold snap.
Is a furnace that trips the breaker dangerous?
It can be. The breaker is protecting the wiring from overheating, so ignoring repeated trips risks a damaged motor or an electrical fire. Switch the furnace off if it trips twice, and call. A burning smell, smoke or a hot breaker means leave it off. Keep your carbon monoxide alarms working.
Should I call an electrician or an HVAC technician?
Start with a furnace technician, since the fault is usually in the furnace’s motors, ignitor, board or wiring. If they find the furnace healthy and the circuit overloaded or the breaker worn, an electrician handles the panel and house wiring.
Who can fix a furnace tripping the breaker in the GTA?
Assurance HVAC Heating & Cooling sends technicians to homes in Toronto, North York, Richmond Hill, Vaughan, Markham, Mississauga and Oakville. Every major brand is serviced, our TSSA-certified gas technicians do the work, the phone is answered 24/7, and nothing is done until you accept the flat-rate price.
Still no heat? We’ll call you back to book a technician.
Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.
Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies
