Skip to content
Gas furnace and water heater in a home basement
Brands we repair

Goodman furnace repair in Toronto

(647) 692-0819Open 24/7, day or night

Goodman furnace repair is a regular part of our work when a unit stops heating, short cycles or won’t light. We handle furnace repair in Toronto and across the GTA, and our technicians work on Goodman Manufacturing furnaces. This page covers what is worth knowing about the brand, the usual repairs, safe checks and how to read a repair against a replacement.

Request a technician

Tell us what’s going on. We’ll call to confirm a time.

What do you need?
How soon? Optional
Add email, details or text updatesOptional

Or call (647) 692-0819Used only to book your visit. Privacy

Key takeaways

  • Goodman is a subsidiary of Daikin Group, and we repair it as an independent contractor.
  • Note the control board’s code before you cut power; the code table below explains it.
  • Ignitors, flame sensors, pressure switches and blower motors are the usual repairs.
  • TSSA-certified gas technicians, a flat-rate price you agree to before work starts.
  • Open 24/7 for no-heat emergencies in Toronto, North York, Vaughan and beyond.

Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.

On this page
  1. Goodman furnace repair in Toronto and the GTA
  2. Who makes Goodman furnaces?
  3. What Goodman says about its furnace features
  4. Signs your Goodman furnace needs repair
  5. Common repairs on a Goodman gas furnace
  6. Goodman furnace error codes: what EE0, EE2 and EE3 mean
  7. Safe checks before you book Goodman furnace repair
  8. Finding your Goodman’s model, serial number and age
  9. Goodman furnace warranty and registration
  10. Repair or replace a Goodman furnace?
  11. Gas smell or a carbon monoxide alarm
  12. What a Goodman repair visit looks like
  13. Goodman furnace repair questions

Goodman furnace repair in Toronto and the GTA

We repair Goodman gas furnaces in Toronto, North York, Richmond Hill, Vaughan, Markham, Mississauga and Oakville, on any day of the week. A TSSA-certified gas technician diagnoses the furnace, explains the fault in plain terms and gives you a flat-rate price to agree to before any part is replaced.

We are an independent contractor, not affiliated with Goodman. Our Goodman furnace repair visits follow the same steps whatever the furnace’s age.

Who makes Goodman furnaces?

Goodman Manufacturing is an independent subsidiary of Daikin Group. Daikin agreed to buy Goodman Global in August 2012, and the company was renamed Daikin Comfort Technologies North America in April 2022.

The same reference says Goodman bought Janitrol in 1982 and still lists it as a brand, which is why some furnaces carry a Janitrol badge.

What Goodman says about its furnace features

Goodman’s US site groups its gas furnaces into 90%+ AFUE and 80% AFUE families and lists multi-speed PSC blowers, multi-speed ECM blowers and a tubular heat exchanger with what it calls wrinkle bend technology. Line names and availability can differ in Canada.

Goodman’s GR9S92 page, for one, lists up to 92% AFUE, a single-stage gas valve, a multi-speed ECM blower, a silicon nitride igniter and a self-diagnostic control board.

Features Goodman lists, and the part a technician checks when it misbehaves
Feature on the maker’s pageWhat it doesWhat fails when it misbehaves
Silicon nitride igniterLights the burners without a standing pilotNo glow, a weak glow or burners that never catch
Multi-speed ECM blowerMoves heated air through the ductsWeak airflow, noise, or a blower that won’t start
Self-diagnostic control boardShows a status or fault patternA lockout that repeats after a reset

Signs your Goodman furnace needs repair

A furnace usually warns you before it quits, and catching the early signs often means a smaller repair, a lower bill and a warmer house. Any of the following is a reason to book a visit, and a few of them mean the furnace should stay off.

  • Warm air that is lukewarm or never arrives, or a house that takes much longer to heat
  • Burners that light, then shut off within seconds
  • Clicking, a humming inducer or a blower that rattles
  • A status light that blinks a repeating pattern
  • Short cycling, where the furnace starts and stops without finishing a cycle

Common repairs on a Goodman gas furnace

Most Goodman repairs involve a part in the start-up chain or the airflow path, and most can be finished in one visit. We test each part rather than swapping parts until the furnace runs, because a failed part often has a cause behind it.

  • Hot surface igniter: a ceramic element that weakens with age and may crack without looking damaged
  • Flame sensor: a thin rod that coats over time and shuts the burners down right after they light
  • Pressure switch and inducer motor: these confirm the venting is drawing before the gas valve opens
  • Limit and rollout switches: they open when the furnace overheats or flames roll out
  • Blower and ECM motor: a worn or failed motor weakens airflow and can trip the limit switch
  • Control board: a short or failed relay stops the whole start-up sequence
  • Condensate trap and drain: on 90%+ models a blocked trap can stop the furnace

Goodman furnace error codes: what EE0, EE2 and EE3 mean

On the GR9S96, GD9S96 and GR9S92 single-stage furnaces, the control board shows a three-character code, not a blink count. The table comes from Goodman’s GR9S96 installation manual (opens in a new tab), pages 41 to 43. A furnace that blinks a light instead has a different control and label.

Note the code before you switch the furnace off. A code names the circuit to test, not the failed part, and a reset only repeats it if the cause is still there.

Status codes for the Goodman GR9S96, GD9S96 and GR9S92 only, from the installation manual
CodeWhat it meansWhat to do
IdLIdle: no call for heat and no faultNothing; this is normal
EE0Locked out after three tries to light, or the flame was lost after lightingBook a repair
EE2The pressure switch never closed: a blocked vent, intake or drain, the switch hose or a weak inducerClear snow from the outdoor pipes by hand; if it returns, book a repair
EE3The primary limit opened on heat, often from a clogged filter, blocked ducts or a blower problemReplace a dirty filter, then call a technician
EE4Flame sensed when the furnace is not calling for heatCall a technician
EE5The fuse on the control blew, or the low voltage wiring has a shortBook a repair
EE6Weak flame signal, usually a coated or misplaced flame sensor; heat may still runBook a repair
EELFault in the igniter circuit: a shorted or loose igniter, its wiring or a poor groundBook a repair
E11The rollout switch has openedCall a technician
NoneBlank display: no power to the furnace or board, a blown fuse or a tripped breakerCheck the furnace switch and breaker; if still blank, book a repair

Write down the code and what the furnace was doing. The board also stores recent faults, so our TSSA-certified gas technicians read that history on site and test the part the code points to before replacing anything.

Safe checks before you book Goodman furnace repair

Four quick checks sort out a surprising number of no-heat calls before a technician is needed, and none of them involve opening the furnace or touching any wiring. Work through them in this order.

  • Thermostat set to Heat, with the setpoint a few degrees above the room temperature and fresh batteries if it takes them
  • The furnace service switch, which looks like a light switch, and the furnace breaker in your panel
  • A clean filter, and the blower door pushed fully shut so its safety switch closes
  • Snow or ice off the outdoor intake and exhaust pipes on a high-efficiency model, cleared by hand

If the furnace still won’t run, try one reset at the service switch and stop there. Repeated resets only repeat the same lockout. Our guide to a furnace not turning on walks through the sequence.

Finding your Goodman’s model, serial number and age

The rating plate holds the model and serial numbers, and having them ready lets us look up the unit before we arrive. The sources we reviewed don’t say exactly where it sits on a Goodman furnace, so look inside the cabinet door or on the side panel, and don’t unscrew anything to find it.

We don’t decode manufacture dates from serial numbers here; the technician can tell you the age from the paperwork and the unit.

Goodman furnace warranty and registration

Daikin’s US warranty page links to a Goodman warranty registration and lookup site. We can’t quote a length or a registration deadline for a Canadian furnace, so check Goodman’s Canadian warranty page for your model and keep your installation paperwork.

Any Goodman furnace repair we do carries our own written workmanship warranty. We don’t do warranty work for the maker, so check with Goodman before approving a part you think is covered.

Repair or replace a Goodman furnace?

A gas furnace usually lasts 15 to 20 years, so age is the first thing we weigh. A worn igniter or sensor is nearly always worth fixing. A cracked heat exchanger or a string of breakdowns on an old unit points toward replacement.

How the decision usually goes
SituationUsual answer
Under about 10 years old, one failed partRepair
10 to 15 years old, a common part such as an igniter or sensorRepair, then watch the next season
15 to 20 years old, a major part like the control board or blower motorCompare repair and replacement
Any age, cracked heat exchangerReplace; we won’t advise running it

Gas smell or a carbon monoxide alarm

A rotten-egg smell means leave the house, then call Enbridge Gas at 1-866-763-5427 from outside. A carbon monoxide alarm means everyone gets out and you call 911. Don’t re-enter to check the furnace.

If a home has a fuel-burning appliance, a fireplace or an attached garage, Ontario requires a CO alarm next to every sleeping area and, from January 1, 2026, on every storey as well, and the province explains the rules on its carbon monoxide safety page (opens in a new tab).

What a Goodman repair visit looks like

We are open 24/7, with technicians out day or night for no-heat emergencies. Booked visits get a two-hour arrival window and a text. The technician tests the start-up sequence, finds the fault and quotes a flat-rate price you approve before work begins.

If you want Goodman furnace repair explained for your own neighbourhood, see our page for furnace repair in Vaughan.

Assurance HVAC Heating & Cooling is an independent HVAC contractor, not affiliated with or authorized by Goodman. Brand names are trademarks of their owners.

FAQ

Goodman furnace repair questions

Why won’t my Goodman furnace light?

Usually the furnace is failing a safety step before the gas valve opens. Common causes are a weak igniter, a blocked vent pipe, a condensate trap that’s backed up or a pressure switch that isn’t closing. Do the thermostat, switch and filter checks, try one reset, then call so a gas technician can test the sequence.

Is Goodman the same company as Daikin?

Goodman Manufacturing is an independent subsidiary of Daikin Group, which agreed to buy Goodman Global in 2012. Goodman’s website carries the Daikin Comfort Technologies North America name. That is ownership only. We can’t say which parts or factories the two brands share, because our sources don’t say.

What does a Goodman furnace flashing light mean?

On a GR9S96, GD9S96 or GR9S92 the board shows a code rather than a blink count. EE0 means it locked out after three failed tries to light, and EE3 means the limit opened, often from a clogged filter. The table above lists the rest. A furnace that blinks a light instead has a different control, so check the label for your model.

Do you only repair Goodman furnaces in certain cities?

No. We repair Goodman gas furnaces in Toronto, North York, Richmond Hill, Vaughan, Markham, Mississauga and Oakville. Each area has its own phone line, and every call is handled by a TSSA-certified gas technician who gives you a flat-rate price before the repair starts.

Is a Janitrol furnace the same as a Goodman?

Goodman bought Janitrol in 1982 and still lists it as a brand. We can’t say that every Janitrol unit matches a Goodman model, so we simply look at the unit in front of us. If yours carries that badge, give the technician the model number from the rating plate.

Can you repair my Goodman furnace if it is out of warranty?

Yes. Warranty status doesn’t change how we diagnose or repair a furnace. Our work carries its own written workmanship warranty. If you think a part may still be covered, find your registration or installer paperwork and check Goodman’s Canadian warranty page before paying for a part.

How long does a Goodman furnace usually last?

Gas furnaces in general last 15 to 20 years, and a Goodman is no different. Lifespan depends on installation quality, filter changes and yearly service. A technician can tell whether an older furnace still has life in it or whether the money is better put toward a new one.

Do you charge for a quote on Goodman furnace repair?

You get a flat-rate price after the technician diagnoses the fault, and you approve it before any work starts. There are no surprise add-ons once you agree. If you decide not to repair, we explain what we found and what your options are, including replacement.

Book a visit

Need Goodman furnace repair? We’ll call you back to book.

Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.

(647) 692-0819

Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies

Request a technician

Tell us what’s going on. We’ll call to confirm a time.

What do you need?
How soon? Optional
Add an email or detailsOptional

Or call (647) 692-0819Used only to book your visit. Privacy