
Furnace installation in Toronto and the GTA
(647) 692-0819Open 24/7, day or night
Furnace installation in Toronto means fitting a new, correctly sized furnace, usually in place of an old one, and Assurance HVAC Heating & Cooling does it across Toronto and the GTA with TSSA-certified gas technicians. Your next step is a home visit: we measure your home’s heat loss, check the ducts and venting, and give you a flat-rate price before anything starts. If your current furnace may still have good years left, our furnace repair team will tell you plainly whether fixing it is the smarter spend.
Key takeaways
- Furnace installation and replacement in Toronto and across the GTA, for all major brands.
- Each new furnace is sized from a heat-loss calculation of your home, never guessed.
- Gas work by TSSA-certified gas technicians, WSIB covered and fully insured.
- A flat-rate price approved before work starts, plus a written workmanship warranty.
- Most straightforward swaps finish in one day. Book online or call for a home visit.
Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.
On this page
- Furnace installation in Toronto: signs it’s time for a new furnace
- Furnace replacement or repair: how to decide
- How furnace installation in Toronto works, from first call to quote
- Furnace installation in Toronto starts with a heat-loss calculation
- Single-stage, two-stage or modulating: which furnace fits?
- High-efficiency furnaces: AFUE, Canada’s 95% minimum and ECM blowers
- Venting a new furnace in a Toronto home
- How to get your home ready for installation day
- Furnace installation in Toronto, step by step
- What affects furnace installation cost in Toronto?
- How to compare quotes from an HVAC contractor
- Pairing a new furnace with central air or a heat pump
- Which new furnace is best for a Toronto winter?
- New furnaces for homes across the GTA
- After the install: warranty, filters and your first tune-up
- Furnace installation questions
Furnace installation in Toronto: signs it’s time for a new furnace
It’s time to price a new furnace when yours is 15 to 20 years old, needs a major part, or breaks down every winter. The signs below are worth a closer look, but none of them alone means the furnace has to go: we find the real fault first, and if repair is the better spend, we say so.
- The furnace is 15 or more years old and repair calls are adding up
- A cracked heat exchanger, or a failed control board on an older unit
- Gas bills climbing while your thermostat settings stay the same
- Rooms that stay cold no matter how long it runs
- Short cycling, starting and stopping every few minutes
- New rattles or a rumble when the burners light
Furnace replacement or repair: how to decide
Repair is usually the better choice when the furnace is younger than about 15 years and a single wear part has failed. Furnace replacement usually wins when the unit is near or past 15 to 20 years, needs an expensive major part, or has needed a technician every Toronto winter for the last few years.
| Question | Lean toward repair | Lean toward replacement |
|---|---|---|
| Age | Under about 15 years | 15 to 20 years or older |
| What failed | One wear part, like an ignitor or flame sensor | The heat exchanger, control board or blower motor on an older furnace |
| Breakdowns | The first in years | Every winter, sometimes twice |
| Comfort | Even heat once it’s fixed | Cold rooms and temperature swings even when running |
| Furnace type | Already high-efficiency condensing | Mid-efficiency, venting into the chimney |
You see the repair price and the replacement price together before deciding. One finding settles it: a cracked heat exchanger may allow carbon monoxide into the living space, so the furnace stays off and replacement comes first.
How furnace installation in Toronto works, from first call to quote
Every furnace installation Toronto homeowners book with us starts with a home visit, not a number over the phone. That visit gives us what we need to size the furnace and price the whole job, so you approve one flat-rate price in writing before any work starts.
- Book online or call, and tell us the furnace’s age and what it’s doing.
- We confirm a two-hour arrival window and text you when we’re on the way.
- At the visit, we measure the house for a heat-loss calculation and check the ducts, venting, gas line, electrical and any AC coil.
- You get written options, such as two-stage and modulating models, each priced for the whole job.
- You pick one, and we book an installation day that suits you.
Furnace installation in Toronto starts with a heat-loss calculation
The right size for a new furnace comes from a heat-loss calculation, which works out how much heat your home loses in the coldest Toronto weather based on its size, insulation, windows and air leakage. In Canada, the standard method for this calculation is CSA F280. Copying the old furnace’s label often repeats an oversizing mistake made decades ago.
An oversized furnace heats the air near the thermostat fast, shuts off and fires again minutes later. That short cycling wears out parts, wastes gas and leaves far rooms cooler. An undersized one can run nonstop on the coldest nights without keeping up. New windows, added insulation or a finished basement all change the answer.
Single-stage, two-stage or modulating: which furnace fits?
A single-stage furnace runs at full output every time it turns on. A two-stage furnace spends most of its time on a lower setting and switches to high only when the house needs it. A modulating furnace adjusts its flame in small steps to match the heat your home is losing at that moment.
| Feature | Single-stage | Two-stage | Modulating |
|---|---|---|---|
| How it heats | Full output every cycle | Mostly low, high on the coldest days | Small steps to match the heat loss |
| Comfort | Noticeable temperature swings | Steadier, longer cycles | The steadiest temperatures |
| Noise | Loudest at startup | Quieter on low | Quietest |
| Upfront cost | Lowest | Middle | Highest |
| Good fit for | Smaller homes, tighter budgets | Many two-storey and semi-detached homes | Larger homes, open layouts |
For many Toronto households, a two-stage furnace balances price and comfort well. A floor that always runs cooler usually needs duct or zoning work, whatever the furnace.
High-efficiency furnaces: AFUE, Canada’s 95% minimum and ECM blowers
A high-efficiency furnace is a condensing furnace with an AFUE rating of 90% or higher, meaning at least 90% of the gas it burns over a season becomes heat for your home. It reaches that rating with a second heat exchanger that pulls extra heat out of the exhaust before it leaves the house.
In Canada, a new gas furnace is almost always a condensing one. Under federal energy efficiency regulations, a standard gas furnace made since July 3, 2019 must reach at least 95% AFUE, and only a few special types, such as replacement furnaces for manufactured homes, are allowed less. So replacing an old 80% mid-efficiency furnace, vented up a metal flue, usually means new plastic venting and a drain.
The same rules cap the blower’s electricity use with a fan energy rating. An ECM blower, short for electronically commutated motor, uses less electricity than older blower motors, and variable-speed versions ramp up quietly. Natural Resources Canada’s ENERGY STAR Canada (opens in a new tab) program explains what that label on a furnace stands for.
Venting a new furnace in a Toronto home
Switching from a mid-efficiency furnace to a high-efficiency condensing model changes how the furnace vents. The old metal flue into the chimney is replaced by plastic PVC pipes, typically one bringing in combustion air and one carrying exhaust outside through a side wall, plus a drain line for the water the furnace produces.
Where the pipes and drain go
The vent ends go on an outside wall with the clearances the gas code sets from windows, doors, the gas meter and the ground, which takes planning beside a narrow Toronto side yard. The condensate line runs to a floor drain or a small condensate pump.
What about the water heater on the chimney?
In many older Toronto houses, the furnace and a gas water heater share one chimney. Once the furnace moves to PVC, the water heater vents alone, and a flue sized for two appliances can be too big for one to draft properly. If it needs a liner or new venting, that goes in the quote.
How to get your home ready for installation day
To get ready for a new furnace, clear a path from the door to the furnace room, including stairs and tight basement turns, move stored things away from the furnace and water heater, and plan for the heat to be off for part of the day. It helps to have an adult home at the start and again for the walkthrough at the end.
- Move boxes, shelves and laundry away from the furnace, water heater and the wall where new vent pipes may exit.
- In winter, clear snow along that outside wall so the vent ends can go in.
- Keep pets and children away from the work area and the open doors.
- If your furnace is rented, check what your rental agreement says about removing the unit before you book.
Furnace installation in Toronto, step by step
On installation day, our TSSA-certified gas technicians protect your home, take out the old furnace, set and connect the new one, then test it until every reading is where it should be. Most straightforward swaps are finished in a single day.
- Protect floors and the path to the furnace room.
- Shut off the gas and power.
- Remove the old furnace and its vent connector.
- Set the new furnace and connect the supply and return ducts.
- Run the PVC intake and exhaust and fit the outdoor vent ends.
- Connect the gas line and leak test every joint.
- Route the condensate drain to a floor drain or pump.
- Commission it: combustion, gas pressure, temperature rise and airflow.
- Set up the thermostat and test a full heating cycle.
- Walk you through the furnace and filter, then haul the old unit away.
We handle the permits and inspections the job needs. Every gas connection is made by a gas technician certified through the Technical Standards and Safety Authority (opens in a new tab), Ontario’s fuel safety regulator. Ontario’s Fire Code also calls for a carbon monoxide alarm next to every sleeping area and, since January 1, 2026, on every storey of a home with a fuel-burning appliance, a fireplace or an attached garage, so test yours once the new furnace is running.
What affects furnace installation cost in Toronto?
The cost of furnace installation in Toronto depends on the furnace’s size, efficiency and staging, how much the venting changes, whether the ducts or an AC coil need work, and how easy the furnace room is to reach. After the home visit, you get one flat-rate price for the whole job before work starts.
| Factor | Why it matters |
|---|---|
| Size | Set by the heat-loss calculation. Bigger isn’t better, and it costs more. |
| Efficiency and staging | Two-stage and modulating models with variable-speed blowers cost more. |
| Venting changes | A first move to PVC, a long vent route or a chimney liner for the water heater. |
| Ductwork changes | A new plenum transition, an added return or resized runs. |
| AC or coil matching | The existing coil may need adapting, or replacing if it’s near the end of its life. |
| Access | Tight furnace rooms, finished basements and narrow stairs take longer. |
| Add-ons | A humidifier, media filter or new thermostat in the same visit. |
The price you approve doesn’t change halfway through the job.
How to compare quotes from an HVAC contractor
When you compare written quotes for a new furnace, make sure each HVAC contractor is pricing the same thing: capacity, staging, AFUE and blower type, sized with a heat-loss calculation. A lower number often leaves out venting, permits or removing the old unit.
- Was the size calculated, or copied from the old furnace?
- Are the model numbers, AFUE and staging listed?
- Are venting, the condensate drain, permits and haul-away included?
- Is the gas work done by TSSA-certified technicians with WSIB coverage and insurance?
- Is there a written workmanship warranty?
Many people start by asking neighbours, “Who does good furnace installation near me?” That’s a fine start, as long as the quotes then go side by side. Ask us the same questions about ours.
Pairing a new furnace with central air or a heat pump
With central air, the AC coil sits on top of the furnace and uses its blower, so the two must be matched. If the air conditioner is about as old as the furnace, replacing both together avoids reopening the same coil and plenum connections later.
You can also swap the AC for a cold-climate heat pump. In a dual-fuel or hybrid setup, the heat pump cools and does most of the heating, and the furnace steps in on the coldest Toronto days. Our heat pump installation page covers sizing, and eligible heat pumps may qualify for the Home Renovation Savings Program, with amounts that depend on the home and its current heating fuel. See heat pump rebates for how to check.
Which new furnace is best for a Toronto winter?
The best furnace for a Toronto winter is a condensing model sized from a heat-loss calculation, with two-stage or modulating heat if steady temperatures and low noise matter to you. The brand matters less than sizing, venting and setup, because an oversized premium furnace still short cycles and wastes gas.
We service all the major furnace brands found in Toronto and GTA homes, including Lennox, Carrier, Trane, Goodman, Rheem, Bryant, Amana, Daikin, York and Napoleon, and recommend a model based on your heat-loss numbers, ducts, venting and budget.
New furnaces for homes across the GTA
We install new furnaces across the GTA, in Toronto, North York, Richmond Hill, Vaughan, Markham, Mississauga and Oakville, and in Brampton, Pickering, Ajax, Aurora and Newmarket, with the same heat-loss sizing and flat-rate pricing everywhere. What changes is the house, and with it what the job involves.
Furnace installation in Toronto often means a tight basement room and a shared chimney in a century semi. Across York Region, plenty of houses built in the 1990s and 2000s are replacing their original builder-grade furnace, and older Mississauga homes often still run on original ductwork. Our Vaughan service area page covers local homes and neighbourhoods.
After the install: warranty, filters and your first tune-up
Once your new furnace is running, register it with the manufacturer, keep the invoice with the warranty papers and book its first tune-up for next fall. Many manufacturers ask for registration soon after installation, and many warranties ask for proof of regular maintenance, so read the terms that came with your furnace.
Our written workmanship warranty covers the installation itself. Check the filter monthly, and book furnace maintenance each fall so a technician can clean the burners, check the heat exchanger and clear the condensate drain before the Toronto heating season.
Furnace installation questions
How long does it take to install a new furnace?
Most straightforward replacements, with the new furnace in the same spot and similar venting, take one day, including removing the old unit and full testing. A first switch from a chimney flue to PVC venting, a chimney liner for the water heater or ductwork changes can add time, and your quote includes the expected timeline.
What size furnace does my home need?
The right size comes from a heat-loss calculation, not the old furnace’s label or square footage alone. We look at the house, insulation, windows, air leakage and ducts, then work out the heat it needs on the coldest days of a Toronto winter. Many older furnaces were oversized, so the new one can often be smaller.
Is a two-stage furnace worth the extra cost?
For many homes, yes. A two-stage furnace runs on low most of the winter, so cycles are longer, temperatures steadier and the furnace quieter. The benefit is biggest in two-storey homes with uneven rooms. We price single-stage, two-stage and modulating options side by side so you can compare.
Do I need new ductwork with a new furnace?
Usually not. Most new furnaces connect to the existing ducts with a new transition at the supply and return. We check the ductwork at the home visit, and if a few runs are undersized, a return is missing or joints leak badly, we tell you before you approve the quote.
Can I install a furnace myself in Ontario?
No. The TSSA says any fuel-fired appliance should be installed, serviced and inspected by a TSSA-registered contractor, and under Ontario law furnaces must be maintained by registered contractors, who must hire certified gas technicians. Installing a furnace means connecting gas, venting exhaust and testing combustion, where a mistake can cause a gas leak or carbon monoxide. Our gas work is done by TSSA-certified gas technicians.
How long does a new furnace last?
A gas furnace typically lasts 15 to 20 years. Correct sizing helps, because a furnace that short cycles wears its ignition parts and blower faster. After installation, a yearly tune-up, regular filter changes and keeping the outdoor intake and exhaust pipes clear of snow give it the best chance of reaching the long end of that range.
When is the best time of year to replace a furnace?
The easiest time is spring, summer or early fall, while the old furnace still runs and you can compare quotes without a cold house. Winter installations go ahead too, since that’s when many furnaces fail, and the heat is off only while the old unit is swapped. If yours has already quit, call any time: we’re open 24/7.
Should I replace my air conditioner at the same time?
If your central air is 12 to 15 years old or uses R-22 refrigerant, it’s worth pricing with the furnace. The coil sits on the furnace and relies on its blower, so matched equipment runs better. You could also swap the AC for a cold-climate heat pump. If the AC has good years left, we’ll say so.
Need furnace installation? We’ll call you back to book.
Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.
Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies
