
Furnace installation in Mississauga
(647) 492-6590Open 24/7, day or night
Assurance HVAC Heating & Cooling of Mississauga handles furnace installation in Mississauga, from straightforward swaps in 1990s townhomes to replacing the third furnace in a 1960s Applewood bungalow. We size each new furnace to the house with a heat-loss calculation, our TSSA-certified gas technicians fit it, and you agree to one flat price before work starts. If yours might have a few good winters left, our team for furnace repair in Mississauga will tell you honestly whether fixing it is the better spend.
Key takeaways
- New and replacement furnaces for every kind of Mississauga home, sized to the house.
- Each furnace is sized from a heat-loss calculation of your house, not the old label.
- TSSA-certified gas technicians, WSIB covered and insured, make every gas connection.
- One flat-rate price before work starts, plus a written workmanship warranty.
- Permits, inspections and taking away the old furnace are all part of the job.
Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling of Mississauga service team.
On this page
- Signs your Mississauga home needs a new furnace
- How we size a new furnace for your house
- Planning furnace installation in Mississauga around original ducts
- High-efficiency furnace options: AFUE and condensing models
- Single-stage, two-stage or modulating for a Mississauga house?
- Why the ECM blower matters as much as the burner
- Venting and condensate for a new high-efficiency furnace
- Furnace installation in Mississauga townhomes and semis
- Larger homes in Lorne Park, Mineola and Port Credit
- Hybrid heat for Mississauga homes: a furnace plus a cold-climate heat pump
- A day of furnace installation in Mississauga, start to finish
- What affects the cost of furnace installation in Mississauga?
- Your first Mississauga winter with the new furnace
- Furnace installation questions from Mississauga homeowners
Signs your Mississauga home needs a new furnace
Start pricing a furnace replacement when yours is 15 to 20 years old, needs a major part like a heat exchanger or control board, or has needed a technician every winter for the last few.
- The furnace is past 15 years and the repair bills are adding up
- A technician has found a cracked heat exchanger
- It’s a mid-efficiency unit venting into the chimney and needs a major part
- Rooms stay cold even when it runs for long stretches
- You’ve finished the basement or added space since the old unit went in
How we size a new furnace for your house
The size comes from a heat-loss calculation: an estimate, room by room, of the heat your house gives up on the coldest days, based on its size, insulation, windows, orientation and air leakage. The old furnace’s nameplate doesn’t enter into it, because many original furnaces were oversized and copying them repeats the mistake.
Mississauga houses change over fifty years. A 1970s Erin Mills home may have had its windows replaced, its attic topped up and its basement finished, which shifts both the total load and where the heat needs to go. An oversized furnace satisfies the thermostat in minutes and stops, so far rooms never catch up; the calculation prevents that.
Planning furnace installation in Mississauga around original ducts
In Applewood, Cooksville, Malton, Erindale and Meadowvale, many homes from the 1950s to the 80s still have the ducts they were built with, sized for heating before central air was added. A new furnace can only deliver what those ducts let through, so we check them before choosing a model.
We measure static pressure and look at the returns. Too few returns, a crushed run or leaky joints make a new variable-speed blower work harder and louder than it should. Adding a return or resizing one trunk connection during the install is often enough; replacing all the ductwork rarely is.
In split-levels with one thermostat, a furnace that can run its blower gently for hours does far better than one that blasts and stops.
High-efficiency furnace options: AFUE and condensing models
AFUE tells you how much of the gas a furnace burns over a season ends up as heat in the house. Condensing furnaces are rated 90% AFUE or higher, and new ones sold in Canada today are rated 95% or more. They get there by pulling extra heat from the exhaust with a second heat exchanger.
An 80% AFUE mid-efficiency furnace loses more of its heat up a metal flue. Trading one for a high-efficiency furnace changes the venting and adds a condensate drain, both planned before we quote. Natural Resources Canada explains what the furnace label means on its ENERGY STAR Canada (opens in a new tab) pages.
Single-stage, two-stage or modulating for a Mississauga house?
Staging describes how the burner fires. A single-stage furnace has one setting, full output. A two-stage furnace runs on a lower setting through most of the season and goes to full output on bitter days. A modulating furnace trims its flame in fine steps so heat output closely tracks the house’s heat loss.
| Home | Often a good fit | Why |
|---|---|---|
| Townhome or semi in Churchill Meadows or Lisgar | Single-stage or two-stage | A smaller heat load and a compact mechanical room favour a simpler unit |
| Bungalow in Applewood or Cooksville | Two-stage | Longer, gentler cycles suit one main floor and a basement |
| Back-split or side-split in Erin Mills or Meadowvale | Two-stage or modulating, with an ECM blower | Slow, steady airflow helps even out several short levels |
| Custom home in Lorne Park, Mineola or Port Credit | Modulating, often with zoning | Large, open spaces and more than one zone benefit from fine control |
These are starting points. The heat-loss numbers and ducts make the final call, and we price more than one option.
Why the ECM blower matters as much as the burner
The blower moves all the heat the burner makes, so its motor matters. An ECM, or electronically commutated motor, uses far less electricity than older PSC motors, and variable-speed versions ramp up slowly, run quietly and can circulate air at low speed all day.
That gentle circulation helps Mississauga split-levels and two-storeys with a warm top floor. With central air, the same blower sets the cooling airflow, so furnace and AC coil must be matched.
Venting and condensate for a new high-efficiency furnace
A condensing furnace vents through plastic vent pipes instead of a metal flue, usually two on a side wall, plus a drain for the water it produces. Where those pipes exit, and where the condensate goes, is planned at the quote. If existing plastic venting is reused, we check that it meets current code for reuse.
Vent ends on the outside wall
Vent ends have to sit set distances from openable windows, doors, the gas meter and the ground, and above the usual snow level. On Mississauga townhomes and semis with shared walls the choice of wall is narrower, and in the historic cores of Streetsville and Meadowvale Village we talk through where the pipes will show from the street.
A water heater sharing the chimney in an older Mississauga home
In older Mississauga homes the furnace and a gas water heater may share a chimney. Once the furnace moves to plastic pipe, a flue built for two appliances can be too large for one to draft reliably, so any liner or new water heater venting goes in the quote.
Where the condensate drains
Condensate runs through a trap to a floor drain, or to a small pump if the drain is across the room, and any line near a garage or outside wall is protected from freezing.
Furnace installation in Mississauga townhomes and semis
Townhomes and semis in Churchill Meadows, Lisgar and other areas built from the 1990s on often have compact mechanical rooms. The new furnace has to fit the same footprint, line up with the existing duct connections and vent along a route that respects shared walls, so we measure the space before quoting.
An original furnace from the 1990s is now past the typical 15 to 20 year life, and a compact condensing model usually fits where it stood.
A condo townhouse corporation may need to approve a new vent location, so we review its rules with you first.
Larger homes in Lorne Park, Mineola and Port Credit
Custom homes that replaced original bungalows near the lake in Lorne Park, Mineola, Port Credit and Clarkson often need zoning or two systems. For those, a modulating furnace with zone dampers, or a separate furnace for the upper floor, usually does more for comfort than one oversized unit.
With two furnaces of different ages, we say plainly whether to replace both now or stage the work. Our HVAC contractor in Mississauga page covers the city’s homes in more detail.
Hybrid heat for Mississauga homes: a furnace plus a cold-climate heat pump
Hybrid heat pairs a gas furnace with a cold-climate heat pump in place of central air. The heat pump cools in summer and handles most of the heating in spring, fall and milder winter weather, and the furnace takes over on the coldest days, so you burn less gas without giving up backup heat.
It makes most sense when the AC is 12 to 15 years old or runs on R-22, a refrigerant no longer produced. See heat pump installation for sizing. The Home Renovation Savings Program offers rebates on qualifying heat pumps; amounts vary by house and current heating fuel, and our heat pump rebates page explains how to check.
A day of furnace installation in Mississauga, start to finish
Most straightforward replacements take a single day. The crew lays floor protection, takes out the old furnace, sets and connects the new one, runs the venting and drain, then tests and commissions everything before walking you through the controls.
- Gas and power are shut off, and the old furnace is disconnected and carried out.
- The new furnace is set level and joined to the supply and return plenums.
- Plastic vent pipes are run outside and the vent ends fitted.
- The gas line is connected and every joint is leak tested.
- Combustion, gas pressure, temperature rise and airflow are checked, then the thermostat is set up.
- You learn the filter and controls, and the old unit leaves with us.
We handle the permits and inspections the job needs, and our gas technicians are certified by the TSSA (opens in a new tab), the province’s fuel safety regulator. Test your CO alarms once the furnace is running.
What affects the cost of furnace installation in Mississauga?
The price of a new furnace rests on how big it needs to be, its AFUE and staging, how much venting and duct work the house calls for, whether the AC coil has to be matched, and how awkward the mechanical room is. The home visit settles all of that, and the flat-rate quote you approve covers the whole job.
| Factor | Why it matters |
|---|---|
| Capacity | Comes from the heat-loss numbers; extra capacity adds cost and makes the furnace short cycle. |
| AFUE and staging | Modulating and two-stage models with variable-speed ECM blowers cost more up front. |
| Venting | A first move from chimney to PVC, a long pipe run, or relining the chimney for the water heater. |
| Ductwork | An added return, a resized trunk connection or a new plenum transition. |
| Cooling coil | An older coil may need an adapter to fit the new cabinet. |
| Access and layout | Compact mechanical rooms, finished basements and split-level stairs add labour. |
Once approved, that price doesn’t change partway through.
Your first Mississauga winter with the new furnace
A new furnace comes with a manufacturer’s warranty that may depend on registration and on regular service, so read its terms in the first week. Keep our invoice with those papers, check the filter monthly through the first winter, and plan a tune-up for the following fall.
The work we did is backed by our own written workmanship warranty. Next fall, book furnace maintenance in Mississauga so a technician can confirm the gas pressure, temperature rise and condensate drain are still where we set them.
Furnace installation questions from Mississauga homeowners
Will a new furnace fit in our townhome’s small mechanical room?
Almost always. We measure the room, the door and the path to it before quoting, and choose a furnace whose cabinet, venting and duct connections fit the space. If the water heater or a shelf in a Churchill Meadows or Lisgar townhome limits access, we tell you at the quote, not on installation day.
Can a high-efficiency furnace work with the ducts in our 1960s bungalow?
Usually, yes. Most Mississauga bungalows from that era can take a condensing furnace on their existing ducts, with new sheet metal where the furnace meets the plenums. We measure static pressure first. If a return is missing or a run is badly undersized, that fix is priced in the same quote so the new furnace isn’t starved of air.
Can the new furnace go in on the same day the old one comes out?
For most straightforward replacements, yes. The old furnace comes out, the new one goes in, and it’s tested and running before we leave. A first switch from chimney venting to PVC, a chimney liner for the water heater or duct changes can add time, and you get the expected timeline with your quote.
Is a two-stage furnace worth it in a Mississauga split-level?
Often, yes. A two-stage furnace spends most of the winter on its lower setting, so cycles run longer and the blower keeps air moving between the levels of a back-split or side-split. Paired with an ECM blower, it usually evens out the lowest floor better than a single-stage unit. We price both so you can compare.
Can you replace a furnace in the middle of a Mississauga winter?
Yes. Winter is when plenty of furnaces give out, and installs carry on in the cold. Heat is off only while the swap is under way, and on a straightforward job the new furnace is running before the crew leaves. If your furnace has already quit, call us right away: we’re open 24/7, and a technician comes out day or night for a no-heat emergency.
How do you choose the size of our new furnace?
With a heat-loss calculation, not the old nameplate or the square footage alone. We look at the insulation, windows, air leakage, orientation and finished spaces, then work out the heat the house needs on the coldest days. In older Mississauga homes that have been upgraded over the years, the right furnace is often smaller than the one it replaces.
Our central air is as old as the furnace. Should we replace both?
It’s worth pricing together. The AC coil sits on the furnace and depends on its blower, so a matched pair runs better, and doing both at once avoids reopening the same connections a few years later. A cold-climate heat pump for hybrid heat is the other option. If the AC has good years left, we’ll say so.
Where do you offer furnace installation in Mississauga?
We provide furnace installation in Mississauga from Malton, Meadowvale and Streetsville to Cooksville, Erindale, Port Credit and Clarkson, plus nearby Oakville and Etobicoke. Every job gets a heat-loss calculation, TSSA-certified gas technicians and a flat price before work starts. We service all major brands and recommend a new model from your heat-loss numbers, ducts and budget.
Need furnace installation in Mississauga? We’ll call you back to book.
Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.
Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies
