Skip to content
Technician servicing a wall-mounted boiler
New and replacement boilers

Boiler installation in Toronto and the GTA

(647) 692-0819Open 24/7, day or night

Assurance HVAC Heating & Cooling provides boiler installation in Toronto for century homes with cast iron radiators, additions with in-floor heat and anyone swapping an old boiler for a high-efficiency one. Our TSSA-certified gas technicians size the new boiler to your home’s heat loss and radiators, and give you a flat-rate price before any work starts. If the old one may still be fixable, see boiler repair.

Get an installation quote

Tell us about your home. We’ll call to book a quote visit.

What do you need?
How soon? Optional
Add email, details or text updatesOptional

Or call (647) 692-0819Used only to book your visit. Privacy

Key takeaways

  • Condensing and combi boilers sized to your home’s heat loss and radiators, not the old boiler’s rating.
  • Existing cast iron radiators usually keep working with a new condensing boiler.
  • TSSA-certified G2 and G1 gas technicians do every gas installation.
  • A flat-rate price is approved before work starts, with a written workmanship warranty.
  • Send a request and we book a two-hour window, then text when we’re on the way.

Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.

On this page
  1. When boiler installation in Toronto is due
  2. Is it better to repair the old boiler or replace it?
  3. Can I keep my cast iron radiators with a new boiler?
  4. Condensing boilers: 90% AFUE and what condensing needs
  5. Chimney venting changes when a condensing boiler goes in
  6. Combi boiler, or heat-only boiler plus an indirect tank?
  7. Boiler installation in Toronto starts with the heat loss, not the old rating
  8. Near-boiler piping, expansion tanks and controls
  9. Boilers in Toronto’s century homes, semis and additions
  10. How the installation day runs for a new boiler
  11. Licensed gas work, permits and a written warranty
  12. What affects the cost of boiler installation
  13. Plan boiler installation in Toronto before the heating season
  14. Boiler installation questions

When boiler installation in Toronto is due

A boiler is ready for replacement when it is old, leaking or failing repeatedly, or when parts are no longer available. Boilers often last well over a decade, so age alone isn’t a verdict, but several of these signs together usually are.

  • Water leaking from the heat exchanger or the boiler body, not just from a valve or fitting
  • Repeated lockouts, even after repairs
  • Parts that the maker no longer supplies, so the boiler can’t be fixed
  • Rising gas bills with the same heating habits
  • Soot or scorch marks on the boiler or its venting, which need a technician right away
  • A boiler that cannot keep every zone warm in a Toronto cold snap

Is it better to repair the old boiler or replace it?

Repair is usually the better choice for a single failed part on an otherwise sound boiler, and replacement is better when the heat exchanger leaks or repairs keep returning. After a diagnosis, we give you both prices side by side and tell you what we would choose.

Replacement also lets a Toronto homeowner step up to a condensing boiler, which can lower gas use. If your old boiler only needs a pump or a valve, our technicians can often fix it in a visit, and you keep the money for a planned replacement later.

Can I keep my cast iron radiators with a new boiler?

Yes, in most Toronto homes. Modern condensing boilers work with existing cast iron radiators, and the radiators usually outlast the boiler. We check each radiator, the valves and the piping first, and tell you if anything needs to change before we quote.

Century homes in the Annex, Cabbagetown and Riverdale often still heat with a boiler and radiators. Keeping them in a Toronto century home preserves the heat people like, and avoids tearing into plaster and trim to add ducts that were never part of the house.

Condensing boilers: 90% AFUE and what condensing needs

A condensing boiler is rated 90% AFUE or higher because it pulls extra heat out of the exhaust by condensing the water vapour in it. To do that, it needs a few things an older boiler doesn’t, and each one affects how the installation is planned.

  • Low return water temperatures, so the system runs cooler to let it condense
  • A condensate drain, usually with a neutralizer, to handle the acidic water it makes
  • Plastic venting, PVC or polypropylene as the maker specifies, instead of a metal flue
  • A sealed path for combustion air, often through the side wall
  • Enough radiator surface to heat the rooms at those lower temperatures

Outdoor reset controls lower the water temperature on mild days, which helps the boiler stay in condensing mode and saves gas.

Chimney venting changes when a condensing boiler goes in

An older boiler vents into the chimney, but a condensing boiler vents through plastic pipe out a side wall or the roof. That changes the plan. In Toronto we route the pipe around windows, the gas meter and narrow side yards, which matters in a Toronto semi or row house.

If a gas water heater still shares that chimney, the chimney may be too large for it alone and need a liner, so we check that too. Our TSSA-certified technicians confirm the venting and combustion air meet code before the boiler is fired.

Combi boiler, or heat-only boiler plus an indirect tank?

A combi boiler heats the house and your tap water from one wall-hung unit, while a heat-only boiler heats the radiators and can feed a separate indirect tank for hot water. Which one suits you depends on space, hot water demand and how many bathrooms you have.

Combi boiler compared with a heat-only boiler and indirect tank
QuestionCombi boilerHeat-only with indirect tank
SpaceOne compact unit, no tankBoiler plus a separate tank
Hot waterOn demand, flow limited by the unitStored supply for several fixtures at once
Best forSmaller homes and one or two bathroomsLarger households and busy mornings
ReplacesThe hot water tank and the boilerThe boiler, with the tank reused or replaced
Watch forPeak demand from two showers at onceMore piping and more floor space

If you’re replacing a hot water tank at the same time, our page on water heater installation explains the tank options.

Boiler installation in Toronto starts with the heat loss, not the old rating

A new boiler should be sized from your home’s heat loss and the output of its radiators, not from the old boiler’s label. Insulation, windows and additions have changed since the old one went in, so the old rating is often too big, and an oversized boiler short cycles, which is common in renovated Toronto homes.

We calculate the heat loss room by room in your Toronto house, check the radiator capacity and pick the boiler that matches both. A boiler that is correctly sized runs longer at lower temperatures, which is what a condensing boiler needs to reach its rated efficiency.

Near-boiler piping, expansion tanks and controls

The piping around a boiler decides how well it works. Piping done to the maker’s specification keeps the water flowing at the right rate, removes air and protects the heat exchanger. A new boiler on old piping can disappoint.

  • Primary and secondary loops, so the boiler and the radiator zones get the flow each needs
  • Air separation, so trapped air doesn’t cause noise and cold radiators
  • A properly sized expansion tank and a new pressure relief valve
  • Circulator pumps and zone valves in good condition, or replaced
  • Outdoor reset and zone controls that match the heating schedule

Boilers in Toronto’s century homes, semis and additions

Toronto’s housing is older than much of the equipment in it, and boilers show that most. We install them in the Annex, Riverdale, Cabbagetown, Leslieville and across the rest of Toronto. A century home in Riverdale or Cabbagetown may have its boiler squeezed into a low basement room with the water heater and laundry, so we measure before we quote and choose a compact unit.

Additions and renovated basements sometimes use in-floor radiant heat, which can run on the same boiler with the right controls. Rooms in a Toronto home that were never reached by radiators can sometimes be served by a ductless head, which also gives you cooling in summer.

How the installation day runs for a new boiler

Boiler installation in Toronto is a planned job, and we explain the schedule before we start. Because we don’t know your piping until we see it, we don’t promise a time on the phone, and we tell you when we quote how many days to expect.

  • Shut down and drain the old system, then remove the old boiler
  • Set the new boiler, vent and combustion air, and run the condensate drain
  • Update the near-boiler piping, expansion tank, relief valve and controls
  • Refill, purge the air and balance the radiators
  • Test the gas connection, venting and safety controls
  • Show you the thermostat, pressure gauge and settings, then clean up and haul away the old boiler

Licensed gas work, permits and a written warranty

Boilers burn gas, so installation in Toronto is regulated work. Our TSSA-certified G2 and G1 gas technicians do the gas connection and venting, and we take care of the permits and inspections the job needs. TSSA (opens in a new tab) is the regulator that oversees gas safety in Ontario.

Ontario law requires carbon monoxide alarms beside each sleeping area and, since January 1, 2026, on every storey of a home with a fuel-burning appliance, a fireplace or an attached garage. If you ever smell gas, step outside and call Enbridge Gas at 1-866-763-5427. If a carbon monoxide alarm sounds, get everyone out and call 911.

Every installation comes with a written workmanship warranty, and our technicians are WSIB covered and fully insured. The maker’s equipment warranty is separate, so keep your paperwork and register the boiler.

What affects the cost of boiler installation

The price of a boiler in Toronto depends on the boiler type, the size of the system and how much the piping and venting need to change. We don’t quote sight unseen. After the visit you get one flat-rate price, and nothing starts until you approve it.

What changes the price of a boiler installation
FactorWhy it matters
Boiler typeCombi, heat-only and condensing models cost different amounts
Size and outputLarger homes and more zones need more capacity
VentingA new side-wall route differs from reusing a chimney
Piping and controlsOlder systems may need new near-boiler piping and controls
Indirect tankAdding hot water storage adds equipment and piping
AccessTight basements and long pipe runs add time

Plan boiler installation in Toronto before the heating season

A boiler that dies in January leaves you choosing equipment in a hurry, so a planned replacement in summer or fall is easier in Toronto. In Toronto you can compare options, check the radiators and pick the right size without the pressure of a cold house.

Once the new boiler is in, a yearly service keeps it running efficiently, and many manufacturer warranties ask for proof of regular service. Our maintenance plan covers two visits a year, and you can contact us to book a visit and a quote for your Toronto home.

FAQ

Boiler installation questions

How many days will a boiler swap take?

It depends on the house. A straight swap with similar piping is quicker than a job that changes the venting, adds an indirect tank or updates the near-boiler piping. We explain the schedule when we quote, and we don’t promise a time until we have seen the house.

Can I keep my cast iron radiators?

Usually, yes. A condensing boiler works with most existing cast iron radiators in Toronto homes, including the ones in older Annex and Cabbagetown houses. We check the radiators, the piping and the venting first, then tell you if anything needs to change before you decide.

What is the difference between a condensing and a standard boiler?

A condensing boiler pulls extra heat from its exhaust and is rated 90% AFUE or higher. It needs low return temperatures, a condensate drain and plastic venting. A standard boiler vents hotter gas up a chimney and wastes more heat.

Is a combi boiler right for a Toronto semi?

It can be, especially where space is tight. A combi heats the house and the tap water from one unit, so there is no tank. It suits smaller homes with one or two bathrooms, and we check the gas line and venting before recommending it.

Will the new boiler need a new chimney liner?

A condensing boiler doesn’t use the chimney, but a gas water heater left in it may need a liner because the chimney becomes too large. We check the water heater, the chimney and the venting together and explain what is needed before we start.

Do you handle the permits and gas inspection?

Yes. We take care of the permits and inspections the job needs as part of the installation. Our TSSA-certified gas technicians do the gas connection and venting to code, and before we leave we walk you through the new boiler’s controls, what was done and what the yearly service involves.

What size boiler does my Toronto home need?

That comes from a heat-loss calculation of your home and the output of its radiators, not from the old boiler’s label. Insulation and renovations change the load over time, so the old rating is often too big. We size the new boiler to match.

Does a new boiler come with a warranty?

Every installation we do carries a written workmanship warranty. The maker’s equipment warranty is separate, and many ask for proof of regular service, so keep your paperwork, register the boiler and check the terms on the maker’s Canadian warranty page.

Book a visit

Need boiler installation? We’ll call you back to book.

Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.

(647) 692-0819

Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies

Get an installation quote

Tell us about your home. We’ll call to book a quote visit.

What do you need?
How soon? Optional
Add an email or detailsOptional

Or call (647) 692-0819Used only to book your visit. Privacy