Skip to content
Heating equipment and storage tanks in a utility room
Assurance HVAC Heating & Cooling of Markham

Furnace installation in Markham homes

(647) 496-5598Open 24/7, day or night

Whether it’s the original builder-grade furnace in a 1990s two-storey or a compact high-efficiency unit for a Cornell townhome closet, Assurance HVAC Heating & Cooling of Markham handles furnace installation in Markham from sizing to start-up. Every new furnace is sized with a heat-loss calculation, put in by TSSA-certified gas technicians and priced as one flat rate before work starts. We handle the permits and inspections the job needs. Our HVAC contractor in Markham page covers everything else we do locally.

Get an installation quote

Tell us about your home. We’ll call to book a quote visit.

What do you need?
How soon? Optional
Add email, details or text updatesOptional

Or call (647) 496-5598Used only to book your visit. Privacy

Key takeaways

  • New and replacement furnaces across Markham, from Unionville heritage homes to Cathedraltown and Cornell.
  • Each furnace is sized with a heat-loss calculation, not copied from the old label.
  • Gas work by TSSA-certified technicians who are WSIB covered and fully insured.
  • One flat-rate price for the whole job, approved before work starts.
  • Most straightforward swaps finish in a day, with permits and inspections handled for you.

Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling of Markham service team.

On this page
  1. Is it time to replace your Markham furnace?
  2. Furnace installation in Markham: getting the size right
  3. New furnaces for large homes in Berczy Village, Cachet and Angus Glen
  4. Single-stage, two-stage or modulating?
  5. AFUE and what makes a high-efficiency furnace
  6. Venting a new furnace in Unionville and Markham Village
  7. Compact furnaces for Cornell and Markham Centre townhomes and condos
  8. Checking the ducts in Milliken and Thornhill homes
  9. Hybrid heat: a new furnace plus a cold-climate heat pump
  10. Furnace installation in Markham: a typical install day
  11. What sets the price of furnace installation in Markham?
  12. Comparing furnace replacement quotes
  13. Looking after a new furnace from its first winter
  14. Furnace installation questions from Markham homeowners

Is it time to replace your Markham furnace?

It’s worth pricing a furnace replacement when the unit is 15 to 20 years old, needs a major part, or has needed a repair most winters lately. That describes many original builder-grade furnaces in Markham’s 1990s and 2000s subdivisions, which have reached the point where breakdowns come more often and gas use creeps up.

  • The furnace is past 15 years and the repair quote is for a heat exchanger, control board or blower motor
  • A technician has found a cracked heat exchanger
  • The central air is just as old and nearing the end of its life too

None of these settles it on its own. If repair is the smarter spend, our furnace repair in Markham team will say so plainly.

Furnace installation in Markham: getting the size right

A new furnace should be sized from a heat-loss calculation: an estimate of the heat your house gives up on the coldest nights, built from floor area, insulation, windows, air leakage and the levels you heat. The rating on the old furnace is a poor guide, because the original may have been oversized and the house has often changed since.

In many Markham homes, a basement finished years after move-in, new windows or added attic insulation have shifted the load. We measure the house and check the ductwork before choosing a size.

Too big, and it warms the hallway by the thermostat, stops and soon restarts, wearing parts and leaving far rooms behind. Too small, and it can’t keep up in a cold snap.

New furnaces for large homes in Berczy Village, Cachet and Angus Glen

Furnace installation in Markham’s big two-storey homes takes extra planning. Houses with finished basements, the kind found across Berczy Village, Cachet, Angus Glen, Box Grove and Greensborough, are hard for one furnace to keep even, so the ducts and controls matter as much as the furnace itself.

For these houses, two-stage or modulating burners paired with a variable-speed ECM blower often fit best, because long low-fire cycles move air through every floor more steadily. Where one level still lags, we look at zoning with motorized dampers, an added upstairs return or balancing the existing runs.

Single-stage, two-stage or modulating?

Staging decides how a furnace behaves through a Markham winter. A single-stage model fires at full output every time. A two-stage furnace runs on a lower setting most of the winter and steps up on the coldest days. A modulating furnace trims its flame in small increments to match the heat the house is losing.

How the three furnace types compare
What mattersSingle-stageTwo-stageModulating
Typical cycleShort runs at full outputLong runs on low, high when neededNear-continuous low output
Evenness between floorsMost temperature swingSteadierSteadiest
SoundLoudest start-upQuiet on low fireQuietest
Price to installLowestMiddleHighest
Where it fitsTownhomes and smaller homes on a budgetMany detached two-storey homesLarge homes and open layouts

We price two or three options side by side so you can weigh cost against comfort.

AFUE and what makes a high-efficiency furnace

AFUE tells you how much of a season’s gas actually becomes heat inside the house. A high-efficiency furnace is a condensing model rated 90% AFUE or higher, and new gas furnaces sold in Canada today are rated 95% or more, while an older mid-efficiency furnace venting up a chimney sits around 80%.

A condensing furnace gets there with a second heat exchanger that pulls heat from the exhaust until water condenses, which is why it needs plastic vent pipe and a drain. Many current models also use an ECM blower motor that draws less electricity than older ones.

For what the ENERGY STAR label on a furnace means, see ENERGY STAR Canada (opens in a new tab) from Natural Resources Canada.

Venting a new furnace in Unionville and Markham Village

Moving from a chimney-vented furnace to a condensing one changes the venting completely. The metal flue gives way to plastic vent pipes, usually two on a side wall for combustion air and exhaust, plus a drain for condensate. In older Unionville and Markham Village homes, we plan that route before we quote.

Where the pipes can end

Vent ends have to stay a code-set distance from windows, doors, the gas meter and the ground. In a tight heritage basement the route to an outside wall can be longer, so we choose the wall carefully.

The water heater still on the chimney

If a gas water heater shares the chimney, it vents alone once the furnace moves to plastic venting. An old chimney built for two appliances often drafts poorly with just the water heater, so a liner may be needed, and it goes in the quote.

Compact furnaces for Cornell and Markham Centre townhomes and condos

Townhomes and condos in Cornell and Markham Centre often keep the furnace, or a combi system with an air handler, in a small mechanical closet. Replacing one means checking the cabinet size, service clearances, the vent route and how the new unit meets the existing coil and ducts before we choose a model.

In a condo, building rules may control who can work on in-suite equipment, when work can happen and how the old unit leaves the building, so we review those with you first. On Cornell homes with rear lanes, the vent ends and the outdoor AC unit can compete for the same stretch of wall, so we plan both together.

Checking the ducts in Milliken and Thornhill homes

A new furnace can only deliver what the ducts allow. Many houses in Milliken and the Markham part of Thornhill date from the 1960s to the 80s and still run on their original ductwork, often with few returns upstairs, so we check static pressure and the supply and return sizes before choosing the furnace and blower.

  • Undersized or missing returns that starve the blower of air
  • Leaky joints in the basement trunk line that lose heat before it reaches the rooms
  • Supply runs to upstairs bedrooms that are too small or too long

In most cases the new furnace joins the existing ducts through a new transition piece. If a return needs adding or a few runs need resizing, we show you why and price it before you approve anything.

Hybrid heat: a new furnace plus a cold-climate heat pump

If the central air in your Markham home is as old as the furnace, price both replacements together, and consider making the new cooling unit a cold-climate heat pump. In a hybrid setup the heat pump cools in summer and handles much of the heating, and the furnace takes over on the coldest days.

Air conditioners from the late 1990s often run on R-22, a refrigerant that’s no longer made, so the old indoor coil usually can’t be reused anyway. Doing both together means the coil and plenum only get opened up once.

On the heat pump side, Save on Energy and Enbridge Gas jointly run the Home Renovation Savings Program, which has rebates for eligible models. What a home qualifies for depends on the house and how it’s heated now; our heat pump rebates page explains how to check.

Furnace installation in Markham: a typical install day

A simple swap usually takes one day. The crew covers the floors, shuts off gas and power, takes out the old furnace, sets the new one, connects the ducts, gas line and venting, then commissions it and shows you how everything works before leaving.

  • Floors covered, gas and power off, and the old furnace and flue connector removed
  • The new furnace set level, with the supply and return ducts connected
  • New plastic intake and exhaust piping run outside, or existing plastic venting checked against current code before it’s reused
  • The gas line connected and leak-tested, and condensate piped to a drain or pump
  • Start-up checks of airflow, combustion, gas pressure and the rise in air temperature
  • A full heating cycle run from the thermostat, then the old unit goes out to the truck

The TSSA (opens in a new tab) regulates fuel safety in Ontario and certifies the gas technicians who do this work. Once the new furnace is running, test your carbon monoxide alarms.

What sets the price of furnace installation in Markham?

Furnace installation cost comes down to what the house needs. The capacity from the heat-loss calculation, the staging and blower you choose, any change from chimney to plastic venting, duct or coil work and the time it takes to get equipment in and out all play a part. You see one flat-rate price after the home visit.

What changes the price of a new furnace
FactorWhat it means for the job
CapacitySet by the heat-loss calculation. A bigger furnace costs more and isn’t better if the house doesn’t need it.
Staging and blowerVariable-speed ECM blowers and two-stage or modulating burners add to the cost.
VentingA first move from a chimney to plastic venting, a long route across a finished basement, or a liner for the water heater.
DuctsA new transition, an added upstairs return or resized runs.
AccessTownhome closets, tight heritage basements and finished ceilings take longer.

Once you approve the price, it stays put for the whole job.

Comparing furnace replacement quotes

Furnace replacement quotes in Markham are only comparable when they price the same thing. Check that each one lists the model number, capacity, AFUE, staging and blower type, explains how the size was worked out, and spells out venting, the condensate drain, permits and removal of the old furnace.

  • Was a heat-loss calculation done, or was the old size copied?
  • Do the installers hold TSSA gas certificates, WSIB coverage and insurance?
  • Is the workmanship warranty in writing?

Hold our quote to the same questions.

Looking after a new furnace from its first winter

Register the new furnace with the manufacturer soon after it’s installed, keep the invoice with the warranty papers and put a fall tune-up on the calendar. Read the warranty terms too, since many call for proof of yearly servicing to keep parts coverage.

Check the filter monthly through its first Markham winter, since renovation or construction dust loads it quickly. A yearly visit for furnace maintenance in Markham cleans the burners and flame sensor and clears the condensate trap, and the installation itself is backed by our written workmanship warranty.

FAQ

Furnace installation questions from Markham homeowners

Should we replace our original furnace before it fails?

If it’s past 15 years and needing repairs, planning the replacement is usually easier than waiting. A planned install lets you compare options, pick the date and avoid a rushed decision in a January cold snap. If it still runs well and passes its tune-up, another season is fine.

Can a high-efficiency furnace go into a heritage home in Unionville?

Usually, yes. The main questions are where the plastic intake and exhaust pipes can exit, how the condensate will drain and what happens to a water heater left on the chimney. We look at all three at the home visit and explain before quoting if the house limits the options.

What size furnace does a large Angus Glen or Cachet home need?

No rule of thumb gives a reliable answer. It comes from a heat-loss calculation covering floor area, insulation, windows, air leakage and the finished basement. Often the result is a two-stage or modulating furnace sized closer to the real load than the original, plus duct or zoning changes where a floor lags.

Can you replace the furnace in a Cornell townhome closet?

Yes. We check the closet dimensions, service clearances, vent route and the connection to the existing coil and ducts, then choose a model that fits. Compact high-efficiency furnaces are made for spaces like this, and a closet holding a combi system or heat pump air handler gets the same careful review.

Will our 1970s Thornhill ductwork work with a new furnace?

Usually, with a few adjustments. Houses from that era often have few upstairs returns and some undersized runs, so we measure static pressure and check the duct sizes at the home visit. A new transition is standard, and if a return needs adding or a run needs resizing, you see that work and its price before approving the quote.

Is now a good time to switch our old AC to a heat pump?

If the AC is 12 to 15 years old or runs on R-22, pricing a cold-climate heat pump alongside the new furnace makes sense. The heat pump replaces the AC, shares the furnace blower and ducts, and does much of the heating, with the furnace as backup on the coldest days. The heat pump may qualify for rebates through the Home Renovation Savings Program.

Can I get furnace installation in Wismer or Greensborough?

Phone the local number shown here, or fill in the request form, and we’ll book a home visit with a two-hour arrival window. We provide furnace installation in Markham in both of those neighbourhoods and every other, from Buttonville and Berczy Village to Box Grove, and nearby in Richmond Hill and North York.

Do you handle the permit for a new furnace?

Yes. We handle the permits and inspections the job needs on every furnace installation in Markham, so there’s nothing for you to arrange. We also take the old furnace away, and the whole job, removal included, is covered by the flat-rate price you approve before work starts, and the installation is backed by our written workmanship warranty.

Book a visit

Need furnace installation in Markham? We’ll call you back to book.

Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.

(647) 496-5598

Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies

Get an installation quote

Tell us about your home. We’ll call to book a quote visit.

What do you need?
How soon? Optional
Add an email or detailsOptional

Or call (647) 496-5598Used only to book your visit. Privacy