
If you have an older mid-efficiency furnace, its replacement will almost always be a high-efficiency condensing model, since nearly all new gas furnaces sold in Canada are condensing. In the high-efficiency vs mid-efficiency furnace comparison, the difference comes down to how much heat each one pulls from the gas, how it vents and what that means for your house. This guide compares them side by side, explains what AFUE means, and points to furnace installation if you are ready to size a new one.
Key takeaways
- Mid-efficiency furnaces run around 80% AFUE and vent up a metal flue or chimney.
- High-efficiency condensing furnaces reach 90% AFUE or higher and vent through plastic pipe.
- High-efficiency models make condensate, so they need a drain, and cost more upfront.
- Your venting, chimney and ductwork shape the cost of replacing a mid-efficiency furnace.
- A heat-loss calculation sizes the new furnace, and the price is flat-rate and approved first.
Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.
On this page
- High-efficiency vs mid-efficiency furnace: the short version
- What AFUE actually tells you
- How each type of furnace works
- Side-by-side comparison
- High-efficiency vs mid-efficiency furnace venting and your chimney
- High-efficiency vs mid-efficiency furnace running costs
- Repairs, lifespan and maintenance differences
- Efficiency is not the same as comfort
- High-efficiency vs mid-efficiency furnace: what replacing yours involves
- How to tell which furnace you already have
- Installation, sizing and what to ask your installer
- Gas and carbon monoxide safety with either furnace
- High-efficiency vs mid-efficiency furnace: common questions
High-efficiency vs mid-efficiency furnace: the short version
A mid-efficiency furnace turns roughly 80% of its gas into heat and sends the rest, hot, up a chimney or metal flue. A high-efficiency furnace is a condensing model rated 90% AFUE or higher, and it captures most of that exhaust heat before venting cool, damp exhaust through plastic pipe.
The extra efficiency costs more upfront and adds a condensate drain, but it uses less gas for the same heat. What the swap involves depends on your home, how much you heat it and what your venting looks like.
What AFUE actually tells you
AFUE, or annual fuel utilization efficiency, is the share of the fuel a furnace turns into heat for the home over a year. A furnace rated 80% AFUE delivers about 80 units of heat for every 100 units of gas burned, while a 96% model delivers about 96 and loses far less up the vent.
The rating is a yearly average under test conditions, so real results depend on your ducts, thermostat habits and how well the furnace is sized. It is also why the old furnace’s nameplate can’t simply be copied: two furnaces with the same gas input deliver different heat output at different AFUE ratings.
How each type of furnace works
Both furnaces burn gas in a heat exchanger, and the blower pushes house air across it. The difference is what happens to the exhaust. A mid-efficiency furnace has one heat exchanger and a small inducer fan, and its hot exhaust rises up a chimney or metal flue.
A condensing furnace adds a second heat exchanger that wrings out more heat, cooling the exhaust until the water vapour in it turns to liquid. A small inducer fan then pushes that cool exhaust out through plastic pipe. That liquid, the condensate, drains through a trap and tube.
Side-by-side comparison
The table below lays out the practical differences you will notice when comparing the two. It describes costs rather than pricing them, because the figures depend on your home, your venting and the job.
| Feature | Mid-efficiency | High-efficiency (condensing) |
|---|---|---|
| AFUE | Typically around 80% | 90% or higher |
| Venting | Metal flue or chimney | PVC or similar plastic pipe, usually out a side wall |
| Exhaust | Hot | Cool and moist |
| Condensate | None from the furnace | Yes, needs a trap and a drain or pump |
| Combustion air | Usually drawn from the room | Often drawn from outdoors by a sealed intake pipe |
| Upfront cost | Lower | Higher |
| Gas use for the same heat | Higher | Lower |
| Parts and repairs | Fewer parts | More parts, including the secondary heat exchanger, and the condensate trap and drain |
| Winter issues | Chimney draft problems | Frozen vent pipes or condensate lines |
High-efficiency vs mid-efficiency furnace venting and your chimney
Venting is often the deciding factor, because the two furnaces need different exits. A mid-efficiency furnace uses the chimney or a metal flue. A high-efficiency one vents through plastic pipe, usually out a side wall, and needs a clear run for the pipes and a path for the condensate.
If a gas water heater shares the old chimney, switching the furnace to plastic pipe changes how the water heater vents, and the chimney may need a liner or the water heater a new vent. A technician checks this before quoting. Our frozen furnace vent pipe guide covers a winter problem unique to condensing models.
High-efficiency vs mid-efficiency furnace running costs
A high-efficiency furnace uses less gas for the same heat, so it costs less to run each month, but how much less depends on your home. Bigger houses, colder rooms, long winters and high gas use give the efficiency more to work with, while a small, well-insulated home gives it less.
Weigh the monthly savings against the purchase price and the venting and condensate work, and ask for each priced as its own line. Sizing, duct condition and thermostat habits shape real bills as much as the rating does, and a furnace that is too big wastes some of the gain by short cycling.
Repairs, lifespan and maintenance differences
A condensing furnace has more parts that can fail, and a mid-efficiency one has fewer. The secondary heat exchanger, condensate trap and drain, and sealed plastic venting add things to check, on top of the inducer motor and pressure switch both types share. Common faults include a clogged trap or a tripped pressure switch, and they are routine for a technician.
Both kinds last about as long when they are sized and maintained properly, and a gas furnace commonly runs 15 to 20 years. Annual tune-ups matter more for a condensing model, since a blocked drain shuts it down. If yours is acting up, our furnace repair page covers what we fix.
Efficiency is not the same as comfort
AFUE doesn’t tell you how comfortable a furnace is, because that comes from staging and the blower. A single-stage furnace is either fully on or off. A two-stage model runs on low most of the time, and a modulating furnace adjusts its output in small steps for long, even heating.
An ECM blower, the variable-speed kind, moves air gently and uses less electricity than an older motor. High-efficiency models are more often paired with staging and ECM blowers, but they are separate features, so ask about each. Both help even out cold rooms.
High-efficiency vs mid-efficiency furnace: what replacing yours involves
Nearly all replacements are high-efficiency condensing models, so the real questions are the venting route, the condensate drain and what happens to anything sharing the old chimney. Most homes with a simple route to a side wall need little more than new plastic pipe and a drain.
- Expect the biggest savings if you heat a larger or older home through long winters.
- Expect a simple job if a plastic vent can run out a side wall without trouble.
- If the chimney is the only vent route, ask how the new plastic venting will run and what happens to a water heater that shares the chimney.
- Ask about a hybrid with a cold-climate heat pump if you want to cut gas use further.
Rebates for heat pumps are on our rebates page, and the same technician can go over the options for your home.
How to tell which furnace you already have
You can usually tell by looking at the vent and the rating plate. Two white plastic pipes running out a side wall, or one wide concentric pipe, point to a high-efficiency furnace. A metal pipe rising into a chimney or through the roof points to a mid-efficiency one.
A condensate drain tube or small pump near the furnace is another clue, since only condensing models make water. The rating plate or the maker’s paperwork lists the AFUE. Leave the furnace doors closed. If the label isn’t visible, a technician reads it on site.
Installation, sizing and what to ask your installer
Whichever furnace replaces yours, size it with a room-by-room heat-loss calculation, not the old furnace’s output. Oversizing causes short cycling and cold rooms, and many replacements are oversized simply because they copied the old nameplate. We handle the permits and inspections the job needs.
- A written heat-loss calculation, not a guess from the old unit
- A plan for the vent route, intake and condensate drain
- What happens to a water heater sharing the old chimney
- A check of the ductwork and return air before the new furnace goes in
- Staging and blower options, and what each adds
- A flat-rate price and a written workmanship warranty
Gas and carbon monoxide safety with either furnace
Both furnaces burn gas, so the same safety rules apply. If a home has a fuel-burning appliance, a fireplace or an attached garage, Ontario requires a carbon monoxide alarm next to every sleeping area and, from January 1, 2026, on every storey as well. Keep yours working, and know what to do before you need it. A new furnace has better controls, but alarms are still your backup.
- Smell gas? Leave at once without using switches or a phone inside, then call Enbridge Gas on 1-866-763-5427 from outside.
- If a carbon monoxide alarm sounds, get everyone, pets included, out of the house and call 911.
Enbridge publishes natural gas safety (opens in a new tab) advice, and ENERGY STAR Canada (opens in a new tab) explains how efficiency ratings work.
High-efficiency vs mid-efficiency furnace: common questions
Is a high-efficiency furnace worth the extra cost?
It often is, because it uses less gas for the same heat, and nearly all new gas furnaces are condensing anyway. The extra cost to plan for is venting and condensate work: new plastic pipe, a drain or pump, and possibly a chimney liner or a new water heater vent. Ask your installer to price those items clearly.
What AFUE is considered high-efficiency?
A condensing furnace rated 90% AFUE or higher is considered high-efficiency, and many models reach the mid-90s. Mid-efficiency furnaces sit around 80%. The rating is the share of the fuel that becomes heat for the house over a year, and the rest leaves through the vent.
Can I replace a mid-efficiency furnace with a high-efficiency one?
Yes, but the venting changes. The new furnace vents through plastic pipe and needs a condensate drain, and if a gas water heater shares the old chimney, its venting may need work. A technician checks the vent route and the chimney before quoting, and handles the permits and inspections.
Why does a high-efficiency furnace have a drain?
Because it pulls so much heat out of the exhaust that the water vapour in it condenses into liquid. That condensate drains through a trap and tube to a floor drain or a small pump. A blocked drain or trap can shut the furnace down, so it is part of every tune-up.
Do high-efficiency furnaces break down more often?
They have more parts to check, such as the secondary heat exchanger and condensate drain, and winter freezing of vent pipes or drains is a known issue. With yearly maintenance and good installation they last as long as mid-efficiency models, commonly 15 to 20 years.
Does a high-efficiency furnace need a chimney?
No. It vents through plastic pipe, usually out a side wall, and often draws combustion air through a sealed intake pipe. The old chimney may still be used by other appliances, such as a gas water heater, and may need a liner or a change when the furnace is replaced.
Is a two-stage furnace the same as a high-efficiency furnace?
No. Efficiency is the AFUE rating, and staging describes how the burners and blower adjust. A furnace can be high-efficiency and single-stage, or two-stage or modulating at different efficiency levels. Staging and an ECM blower add comfort, so ask about each separately.
Who can help me choose a furnace in the GTA?
Assurance HVAC Heating & Cooling sizes and installs furnaces across Toronto, North York, Richmond Hill, Vaughan, Markham, Mississauga and Oakville. A TSSA-certified gas technician does a heat-loss calculation, explains what your venting and drain need, and gives a flat-rate price you approve before work begins.
Planning a replacement? We’ll call you back to book a quote visit.
Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.
Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies
