
Furnace installation in North York
(647) 584-3959Open 24/7, day or night
Assurance HVAC Heating & Cooling of North York handles furnace installation in North York for homes at both ends of the local range: post-war bungalows that often need a smaller furnace than the one they have, and large custom rebuilds that need steady heat across several floors. Every new furnace is sized with a heat-loss calculation and installed by TSSA-certified gas technicians for one flat price. If yours may still be worth fixing, our team for furnace repair in North York will say so.
Key takeaways
- New and replacement furnaces for North York bungalows, split-levels and custom homes.
- Sized from a room-by-room heat-loss calculation, never copied from the old label.
- Installed by TSSA-certified gas technicians who are WSIB covered and insured.
- One flat price for the whole job, approved before work starts, with a written warranty.
- Most straightforward swaps take a single day. Book a home visit online or by phone.
Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling of North York service team.
On this page
- Furnace installation in North York: when the old furnace should go
- Sizing a new furnace with a heat-loss calculation
- Furnace installation in North York bungalows and split-levels
- Two-stage, modulating or a second furnace for larger homes
- High-efficiency furnace ratings: AFUE and ECM blowers
- Venting and condensate changes in older houses
- Checking the ducts before the new furnace goes in
- Pairing the furnace with a cold-climate heat pump
- Replacing the furnace during a renovation or addition
- What happens on installation day
- What does furnace installation in North York cost?
- Questions to ask before you sign a furnace quote
- After the install: registration, records and the first tune-up
- Furnace installation questions from North York homeowners
Furnace installation in North York: when the old furnace should go
Start pricing a new furnace when yours is near or past 15 to 20 years, needs a major part such as a heat exchanger or control board, or has needed a repair call most winters. Climbing gas bills, a house that never feels even and a furnace that runs in short bursts are reasons to look at furnace replacement too.
- A furnace 15 years old or more, with repairs getting more frequent
- A cracked heat exchanger found on a service call
- A mid-efficiency furnace that still vents into the chimney
- A basement finish, new suite or addition on the way
None of these alone means the furnace must go. If a repair is the smarter spend, we say so.
Sizing a new furnace with a heat-loss calculation
A heat-loss calculation works out how much heat the house loses on the coldest days, room by room, from its walls, windows, insulation, air leakage and size. That number, not the label on the old furnace, decides the capacity of the new one. In older North York homes it often comes out lower than people expect.
Over the decades, many post-war bungalows have gained new windows, more attic insulation and a finished basement, and each of those changes how much heat the house needs. Large North York rebuilds carry the opposite risk: open foyers and big windows lose heat quickly, and a guess from square footage can leave the upper floor short.
Furnace installation in North York bungalows and split-levels
In the bungalows, split-levels and backsplits of Bathurst Manor, Lawrence Manor, Parkwoods and Don Mills, the ductwork usually sets the limits. It was laid out when the basement was storage space and the furnace was the first one the house had, so a new high-efficiency furnace has to match what those ducts can really move.
We measure static pressure on the existing ducts before choosing equipment. If it runs high, an added return, a larger trunk or a deeper filter cabinet brings it down, and a variable-speed ECM blower set up for those ducts keeps the airflow quiet.
Split-levels and backsplits spread rooms over several half-floors on one trunk line. As an HVAC contractor in North York, we check that each level gets its share of air and that the thermostat isn’t mounted in the warmest spot.
Two-stage, modulating or a second furnace for larger homes
In York Mills, Hogg’s Hollow, Bayview Village and Armour Heights, the question is often less about size and more about control. A two-stage furnace or a modulating furnace with a variable-speed blower runs long, gentle cycles that even out temperatures between floors, and some North York layouts are better served by two separate systems.
| Option | How it runs | Where it fits best |
|---|---|---|
| Single-stage | Full flame every time it starts | Smaller bungalows with simple layouts |
| Two-stage | Low fire most of the winter, high on the coldest days | Many bungalows, split-levels and two-storey homes |
| Modulating | Adjusts the flame in small steps to match heat loss | Large open rebuilds and zoned homes |
| One system, zoned | Motorized dampers and several thermostats | Homes whose ducts split cleanly by floor |
| Two systems | A separate furnace or air handler upstairs | Three-storey homes with long duct runs |
High-efficiency furnace ratings: AFUE and ECM blowers
A high-efficiency furnace is a condensing furnace rated at 90% AFUE or higher, and new gas furnaces sold in Canada today are rated 95% AFUE or more. AFUE measures how much of the gas burned over a season becomes heat in your home.
The blower matters as much as the burner. An ECM, short for electronically commutated motor, draws less electricity than an older PSC motor, and variable-speed versions run quietly at low speed through the long cycles of a two-stage or modulating furnace. Natural Resources Canada’s ENERGY STAR Canada (opens in a new tab) program explains what its label means.
Venting and condensate changes in older houses
Moving from a mid-efficiency furnace to a condensing one changes the venting. Instead of a metal flue into the chimney, the new furnace vents through plastic pipe, usually one for combustion air and one for exhaust, exiting a side wall, along with a condensate line to carry away water. We plan the whole route before quoting.
Where the pipes come out
Vent ends need code clearances from openings like windows and doors, from the gas meter and from grade, so a narrow North York side yard takes some planning. We also keep them away from spots where shovelled snow piles up. If the house already has plastic venting from an earlier condensing furnace, we check that it meets current code for reuse.
When the bungalow water heater is left on the chimney
Once the furnace moves to plastic venting, a gas water heater left alone in an oversized flue can draft poorly. We test it, and any chimney liner or new vent it needs is priced into the quote.
Condensate in a finished basement
The drain line runs to a floor drain, or to a small pump when the drain is across a finished room, routed where it won’t freeze or end up behind drywall.
Checking the ducts before the new furnace goes in
A new furnace can only perform as well as the ducts it connects to. Before we quote, we look at the supply and return runs, measure static pressure and check for crushed or disconnected sections, which often hide behind basement bulkheads. Fixing those can do more for comfort than a bigger furnace ever would.
- Return air: enough grilles, not blocked by furniture or a renovation
- Static pressure: measured against what the new blower can handle
- Leaky joints near the furnace sealed with mastic or foil tape
- Basement runs added or rebalanced when the space has become a living area
Pairing the furnace with a cold-climate heat pump
If your central air conditioner is as old as the furnace, consider replacing it with a cold-climate heat pump at the same time. In a hybrid setup the heat pump cools in summer and carries much of the winter heating, and the new furnace takes over on the coldest days of a North York winter.
Doing both together means one set of coil connections and matched equipment. Eligible heat pumps may qualify for Home Renovation Savings Program rebates, and what you receive depends on your house and the fuel you heat with now. Our heat pump rebates page explains how to check.
Replacing the furnace during a renovation or addition
Basement finishes, additions and second-storey extensions are good moments to replace an aging furnace. With walls and ceilings open, we can size the new furnace for the finished North York house, rearrange ducts and returns, and route the venting and condensate cleanly instead of working around new drywall later.
A new basement apartment can also get its own heat, often a ductless heat pump with its own thermostat. We work around your renovation schedule so the ductwork is done before the ceilings close.
What happens on installation day
Most straightforward replacements are finished in one day. Our TSSA-certified gas technicians protect the floors and stairs, remove the old furnace, set and connect the new one, then test it until combustion, gas pressure, temperature rise and airflow are where they belong. The heat is off for only part of the day.
- Floors protected, gas and power shut off, and the old furnace carried out
- New furnace set level, with supply and return transitions built to fit
- Plastic venting and condensate line installed with the right pitch
- Gas line connected and every joint leak-tested
- Commissioning, thermostat setup and a walk-through of the filter and controls
We handle the permits and inspections the job needs and haul the old furnace away. Every gas connection is made by a G2 or G1 technician certified through the TSSA (opens in a new tab).
What does furnace installation in North York cost?
Furnace installation cost depends on the new furnace’s capacity, efficiency and staging, how much the venting changes, what the ducts need and how easy the furnace room is to reach. A like-for-like bungalow swap and a two-furnace custom home have little in common, so we price each one after a home visit.
| Cost factor | What it means in a North York home |
|---|---|
| Capacity | Set by the heat-loss calculation, often smaller than the old furnace in a bungalow |
| Staging and blower | Two-stage and modulating furnaces with variable-speed blowers cost more upfront |
| Venting | A first switch from chimney to plastic venting, a long route, or a liner for the water heater |
| Ducts and returns | Added returns, resized runs or new branches for a finished basement |
| Number of systems | A second furnace or a zoning panel for a large home |
| Access | Tight utility rooms and narrow basement stairs add time |
Once you approve the flat price, it holds for the whole job, including removal of the old unit.
Questions to ask before you sign a furnace quote
Comparing quotes for furnace installation in North York only works when each one prices the same thing. Ask every installer for the model number, AFUE, staging and blower type, and how they worked out the size. A lower total often leaves out venting changes, the condensate drain, permits or haul-away, which can turn up later as extras.
- Was the size calculated, or matched to the old furnace?
- Is the water heater’s venting covered if the furnace leaves the chimney?
- Are permits, inspections and removal of the old furnace included?
- Are the gas technicians TSSA certified, with WSIB coverage and insurance?
- Is the workmanship warranty written down?
After the install: registration, records and the first tune-up
Register the new furnace with its manufacturer soon after installation, keep the invoice with the warranty booklet, and plan the first tune-up for next fall. A furnace warranty may require proof of regular maintenance, so keep every service record with those papers.
We put our own workmanship on the install in writing. A yearly visit for furnace maintenance in North York keeps the new furnace clean and adjusted, and adds a dated service record each year.
Furnace installation questions from North York homeowners
Does a North York bungalow need a smaller furnace than the one it has?
Often, yes. Many furnaces in post-war bungalows were sized generously, and later upgrades like new windows and attic insulation cut the heat the house needs. A heat-loss calculation gives the real figure. A right-sized furnace runs longer, quieter cycles, heats the far rooms more evenly and is easier on undersized ducts.
Can you install a new furnace without opening up my finished basement?
Usually. Most new furnaces go in the same spot as the old one and connect to the existing ducts with new transitions. Switching to plastic venting or adding a return sometimes means opening a ceiling panel or a small section of drywall. We plan the route at the home visit and tell you what’s involved before you approve the quote.
Is a modulating furnace worth it in a large home?
In the open, multi-floor rebuilds of York Mills and Bayview Village, it often is. A modulating furnace matches its output to the heat the house is losing, so cycles are long and temperatures steady, especially with zoning. In a simpler two-storey North York home, a two-stage furnace may give most of the benefit for less. We price both.
Is furnace installation in North York a one-day job?
A one-day job is typical when the new furnace goes where the old one stood and the venting stays similar. That day covers carrying out the old unit and testing the new one. Converting to plastic venting, lining the chimney for the water heater, changing ducts or adding a second system takes longer, and your quote includes the expected schedule.
What if the old furnace dies before I’ve chosen a new one?
Call the North York line on this page. A technician comes out day or night for a no-heat call, and if a safe repair can get you through a few weeks, the technician will say so and price it. If the furnace can’t safely run, we can move ahead with a replacement, and the heat is off only for part of installation day.
Do I need a chimney liner when I switch to a high-efficiency furnace?
Sometimes. In North York bungalows that still run a mid-efficiency furnace, it often shares the chimney with a gas water heater, and once the furnace moves to plastic venting, the water heater may not draft properly alone. We test the draft and inspect the flue. If it needs a liner or a new vent, that cost is in your quote, so it isn’t a surprise later.
Do you offer furnace installation in Newtonbrook or Victoria Village?
We install furnaces across North York, from Newtonbrook and Willowdale to Downsview, Bedford Park and Victoria Village, and in nearby Vaughan, Markham and Richmond Hill. Book a home visit online or by phone. We confirm a two-hour arrival window, text you on the way and measure the house for the heat-loss calculation.
Can I add a heat pump later if I install a furnace now?
Yes, if you plan for it. A furnace with a variable-speed blower and room above it for a matched coil makes adding a cold-climate heat pump later much simpler. Tell us at the home visit and we’ll choose a furnace and thermostat that can run a hybrid system.
Need furnace installation in North York? We’ll call you back to book.
Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.
Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies
