Skip to content
Technician servicing a wall-mounted boiler
Assurance HVAC Heating & Cooling of North York

Boiler installation in North York

(647) 584-3959Open 24/7, day or night

Assurance HVAC Heating & Cooling of North York handles boiler installation in North York for the hydronic systems found here: cast iron radiators in some older Bedford Park houses and in-floor radiant heat in a number of custom builds. Our TSSA-certified gas technicians size the new boiler to your home’s heat loss, not the old boiler’s rating, and quote a flat-rate price first. For a boiler that only needs fixing, see boiler repair in North York.

Get an installation quote

Tell us about your home. We’ll call to book a quote visit.

What do you need?
How soon? Optional
Add email, details or text updatesOptional

Or call (647) 584-3959Used only to book your visit. Privacy

Key takeaways

  • Condensing and combi boiler replacement sized to heat loss, for radiators and radiant floors.
  • TSSA-certified gas technicians handle gas, venting, controls and piping, WSIB covered and insured.
  • We compare combi and heat-only with an indirect tank before you choose.
  • You approve a flat-rate price before work, and the job carries a written warranty.
  • No-heat calls are answered 24/7, with technicians out day or night.

Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling of North York service team.

On this page
  1. Boiler installation in North York: when it is time to replace
  2. North York homes that still rely on a boiler
  3. Replacing a boiler on cast iron radiators in Bedford Park
  4. In-floor radiant heat in North York custom homes
  5. What a condensing boiler needs to work as intended
  6. Combi or heat-only boiler: which suits a North York house?
  7. Boiler installation in North York: sizing to the house, not the old boiler
  8. Near-boiler piping, air separation and outdoor reset
  9. Boiler installation in North York: how the day unfolds
  10. Gas, carbon monoxide and who may install a boiler
  11. What drives the price of boiler installation in North York?
  12. Annual service after the new boiler goes in
  13. Boiler installation questions from North York homeowners

Boiler installation in North York: when it is time to replace

A boiler is ready for replacement when its heat exchanger leaks, it locks out repeatedly, parts are no longer available, or the repair cost nears the cost of a new unit. The age matters less than the condition and the efficiency, though a boiler that is decades old is worth a hard look.

In North York and elsewhere, older boilers waste fuel because their burners and heat exchangers are less efficient than modern ones. A condensing boiler rated 90% AFUE or better can cut the fuel used to heat the same water, which is why many owners replace instead of patching a tired unit.

  • Water at the base of the boiler or rust streaks that point to a leaking heat exchanger.
  • Repeated lockouts or fault codes that return after each reset.
  • Parts that the supplier no longer stocks, leaving each repair as a workaround.
  • Kettling, a loud rumbling that suggests scale or sludge in the heat exchanger.
  • Rising fuel use without any change in the way you heat the house.

North York homes that still rely on a boiler

There are fewer radiator homes here than in older parts of Toronto, but boilers still heat some older houses in Bedford Park and feed in-floor radiant systems in a number of custom builds. Both need a boiler that suits the way the house uses heat.

If your home sits in Lawrence Manor, Bathurst Manor or Willowdale and is mostly forced air, a boiler may only serve a basement addition or a bathroom floor. We install for the zone you actually have.

Replacing a boiler on cast iron radiators in Bedford Park

Cast iron radiators in North York keep working for decades, so replacing the boiler does not mean replacing the radiators. They hold a lot of water and release heat slowly, which pairs well with a boiler that runs at lower temperatures.

Older houses in Bedford Park may have a chimney that once vented a large old boiler. When a condensing boiler goes in, the venting changes, since its cool, acidic exhaust has to vent through the PVC or polypropylene pipe the maker specifies, not the old chimney. We check the existing piping and radiator valves, then plan the venting and controls together.

If the radiators have been painted over or are blocked by furniture, we note that too, since heat output affects the sizing.

In-floor radiant heat in North York custom homes

In North York, radiant floors need a boiler that can run at low water temperature and manage several zones. A number of large custom rebuilds in North York use in-floor radiant heat.

A modern condensing boiler suits radiant heat, because the low return temperatures let it condense and reach its rated efficiency. Mixing valves, zone controls and an outdoor reset are part of the setup. If you are building in Armour Heights or Willowdale and planning radiant floors, bring us in before the slab or subfloor is closed.

What a condensing boiler needs to work as intended

A condensing boiler is 90% AFUE or better, so boiler installation in North York often means condensing, but it only reaches that when the system returns cool water, so the piping and controls matter as much as the boiler. We design the whole system, not just the box.

  • Low return water temperatures, which come from the right radiator size, flow and controls.
  • A condensate drain, with a neutralizer where required, to take the acidic water away safely.
  • Venting in PVC or polypropylene, as the manufacturer specifies, instead of an old metal flue.
  • A combustion air supply that suits the room and the equipment.
  • Gas supply and sizing checked by TSSA-certified technicians.

Where the radiators are large for the house’s heat loss today, we can lower the supply temperature with outdoor reset so the boiler condenses more often. Where they are undersized, the boiler has to run hotter on cold days, and we explain how that affects efficiency.

Combi or heat-only boiler: which suits a North York house?

A combi boiler heats the house and makes hot water on demand, while a heat-only boiler paired with an indirect tank stores hot water for the whole house. The right choice depends on bathrooms, hot water use and space.

Combi boiler compared with a heat-only boiler and indirect tank
QuestionCombi boilerHeat-only with indirect tank
SpaceOne compact unit on the wallBoiler plus a separate insulated tank
Hot waterOn demand, limited by flowStored, so several fixtures can run together
Best fitOne or two bathrooms and moderate useThree or more bathrooms or heavy use
If the boiler is downHeating and hot water stop togetherThe tank still holds stored hot water for a time
UpkeepPlate heat exchanger can scaleTank anode and boiler service

Custom homes with three or four bathrooms usually do better with a larger tank. For hot water on its own, see our page on water heater installation in North York.

Boiler installation in North York: sizing to the house, not the old boiler

In North York, a boiler is sized by a heat-loss calculation of the house and its radiators, not by copying the old boiler’s rating. Many North York houses have been insulated, re-windowed or renovated since their first boiler went in, so the old rating is often too large.

An oversized boiler cycles on and off, wastes fuel and wears out sooner. A right-sized condensing boiler runs longer at lower temperatures, which is how it reaches its rated efficiency.

If you have added a room to your North York home, finished a basement or removed walls, tell us. Each change alters the load, and we calculate it room by room.

Near-boiler piping, air separation and outdoor reset

The piping around the boiler decides how well the system performs, and a good installer in North York treats it as part of the job. We build the near-boiler piping to the manufacturer’s specification and the home’s layout.

  • Primary and secondary loops where the boiler and heating zones need different flows.
  • Air separation and a proper expansion tank, which protect the pumps and keep the system quiet.
  • Circulator pumps and zone valves sized for the load.
  • An outdoor reset control that lowers water temperature on milder days, saving fuel.
  • Isolation valves and drain points, so future service is easier.

If your radiators have always banged or gurgled, tell us. Air and flow problems are often fixed at the same time as the boiler swap.

Boiler installation in North York: how the day unfolds

Most boiler replacements in North York take about a day or two once the plan is set, though radiant systems or new venting can take longer. Booked visits get a two-hour arrival window and a text.

We drain the system, remove the old boiler and set the new one, then connect piping, gas, venting, condensate and controls. Our technicians fill and purge the system, test for leaks, fire the boiler and check combustion before they leave.

We handle the permits and inspections the job needs, and you receive the written workmanship warranty and paperwork for the manufacturer’s own registration.

Gas, carbon monoxide and who may install a boiler

In North York, as across Ontario, gas appliances must be installed by qualified, licensed technicians, and ours are TSSA-certified G2 and G1 gas technicians. The TSSA (opens in a new tab) is the regulator for gas safety in the province.

Ontario requires carbon monoxide alarms adjacent to every sleeping area, and since January 1, 2026 on every storey too, in any home with a fuel-burning appliance, a fireplace or an attached garage, so most homes need more than one. If you smell gas, leave the house and call Enbridge Gas at 1-866-763-5427 from outside. If a carbon monoxide alarm sounds, get everyone outside and call 911.

What drives the price of boiler installation in North York?

The price depends on the type of boiler, the venting route and the condition of the piping and controls. We quote each job after seeing the house and give you a flat-rate price before work starts.

What changes the price of a boiler replacement
FactorWhy it matters
Boiler typeCombi, heat-only and larger condensing models differ in equipment and setup.
VentingMoving from a chimney to PVC or polypropylene changes materials and labour.
Piping conditionCorroded or undersized piping may need replacing as part of the job.
Zones and controlsMore zones, mixing valves and an outdoor reset add parts and setup.
Hot waterAn indirect tank adds equipment but serves larger households better.
Gas and drainA larger gas line or a new condensate route adds work.

You hear the diagnostic fee before we book, you approve the flat-rate price after the assessment, and it does not change halfway through.

Annual service after the new boiler goes in

A new North York boiler should have a yearly service to keep its efficiency. Many manufacturer warranties ask for proof of regular maintenance, so keep your records with your warranty papers.

Our maintenance plan books regular visits and gives you priority booking when something breaks. A good time for the boiler check is early fall, before the first cold week.

FAQ

Boiler installation questions from North York homeowners

How do I know if my North York boiler should be replaced?

Look for leaks at the heat exchanger, repeated lockouts, loud kettling, parts that are no longer available and rising fuel use. If repair costs are near the price of a new unit, replacement is usually wiser. We give you both options in writing.

Will my cast iron radiators work with a new boiler?

Yes. Cast iron radiators in North York homes last for decades, and a new boiler can heat them. We check the piping and valves, size the boiler to the home’s heat loss and plan the venting. Condensing boilers run cooler water, so the controls are set to suit the radiators.

What is a condensing boiler?

A condensing boiler captures heat from its exhaust by condensing water vapour, which lets it reach 90% AFUE or higher. It needs cool return water, a condensate drain and plastic venting. We design the whole system so it can actually reach that efficiency.

Should I choose a combi boiler or a heat-only boiler?

A combi boiler suits homes with one or two bathrooms and moderate hot water use. A heat-only boiler with an indirect tank serves larger households better, because it stores hot water. We count bathrooms and look at space before recommending one.

Can a boiler work with in-floor radiant heat?

Yes, and condensing boilers suit radiant floors well. The system needs low water temperatures, mixing valves, zone controls and often an outdoor reset. If you are building or renovating, plan the boiler and the floor together before the slab or subfloor is closed.

How long does boiler installation take?

Most replacements take about a day or two once the plan is agreed, while radiant systems and new venting can take longer. Booked visits get a two-hour arrival window and a text. We explain the timeline before you approve the flat-rate price.

Do you handle permits and gas work?

Yes. Our TSSA-certified gas technicians do the gas, venting and controls in North York homes, and we handle the permits and inspections the job needs. Every technician is WSIB covered and insured, and the installation carries a written workmanship warranty.

Do you install boilers across North York?

We install boilers in North York homes from Bedford Park and Willowdale to York Mills and Bayview Village. Book online or by phone, and approve a flat-rate price before work starts. Our HVAC contractor in North York page lists everything else we do.

Book a visit

Need boiler installation in North York? We’ll call you back to book.

Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.

(647) 584-3959

Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies

Get an installation quote

Tell us about your home. We’ll call to book a quote visit.

What do you need?
How soon? Optional
Add an email or detailsOptional

Or call (647) 584-3959Used only to book your visit. Privacy