Skip to content
Technician servicing a wall-mounted boiler
Assurance HVAC Heating & Cooling of Richmond Hill

Boiler installation in Richmond Hill

(647) 905-9241Open 24/7, day or night

Most Richmond Hill homes heat with forced air, but some custom homes in Richvale and Bayview Hill use a boiler for in-floor heat. Assurance HVAC Heating & Cooling of Richmond Hill handles boiler installation in Richmond Hill for those homes, with TSSA-certified gas technicians, a heat-loss calculation and a flat-rate price you approve first. If your boiler may only need a fix, see boiler repair in Richmond Hill.

Get an installation quote

Tell us about your home. We’ll call to book a quote visit.

What do you need?
How soon? Optional
Add email, details or text updatesOptional

Or call (647) 905-9241Used only to book your visit. Privacy

Key takeaways

  • Condensing and combi boiler installation for in-floor heat and radiators in Richmond Hill homes.
  • Sized to the home’s heat loss and its radiators or floor loops, not the old boiler’s rating.
  • Gas work by TSSA-certified technicians, WSIB covered and insured, with a written workmanship warranty.
  • A flat-rate price you approve before work starts, with permits and inspections handled.
  • No-heat calls are answered 24/7, and booked visits get a two-hour window.

Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling of Richmond Hill service team.

On this page
  1. Boiler installation in Richmond Hill: which homes have one
  2. Is it time for boiler installation in Richmond Hill? Signs to look for
  3. Condensing boilers: higher efficiency and what they need
  4. Combi, or a heat-only boiler paired with an indirect tank?
  5. Sizing boiler installation in Richmond Hill to the home, not the old boiler
  6. Custom homes in Richvale and Bayview Hill with in-floor heat
  7. Cast iron radiators and a new boiler
  8. Venting changes when a condensing boiler goes in
  9. Piping, air removal and controls around the boiler
  10. Boiler installation in Richmond Hill, from shutdown to first fire
  11. Gas safety and licensed work
  12. What goes into boiler installation cost in Richmond Hill
  13. Yearly service for the new boiler
  14. Boiler installation questions from Richmond Hill homeowners

Boiler installation in Richmond Hill: which homes have one

Boilers are the exception in Richmond Hill, where most homes use forced air. Our HVAC contractor in Richmond Hill team covers both. Some custom homes in Richvale and Bayview Hill use a boiler for in-floor heat in basements, garages or bathrooms. Those are the Richmond Hill homes where a replacement boiler matters.

If your house has forced air only, you may be looking for a furnace instead, and our page on furnace installation in Richmond Hill covers that. If you are not sure what heats your house, tell us what you see in the basement and we will help you work it out.

Is it time for boiler installation in Richmond Hill? Signs to look for

A boiler in a Richmond Hill home is usually worth replacing when it is old, leaking from the heat exchanger, locking out repeatedly or waiting on parts that are no longer made. One of these signs alone may not decide it, but together they point to a new boiler.

  • The boiler is well past 20 years old and has needed several repairs
  • Water is leaking from the heat exchanger or the body of the boiler
  • Repeated lockouts or fault codes that a repair does not cure
  • A technician reports that parts are no longer available
  • Rust, scale or sludge in the system water, and noisy, rumbling operation
  • Gas bills that keep climbing while comfort drops

Boiler lifespan varies by type and water quality, so we look at condition and repair history, not age alone.

Condensing boilers: higher efficiency and what they need

A condensing boiler recovers heat from its exhaust, which puts its efficiency at 90 percent AFUE or better. To get that efficiency it needs the return water to run cool, a condensate drain with a neutralizer, and sealed venting in the material the maker specifies.

In practice, a Richmond Hill house needs a system that suits it. Low-temperature in-floor loops are a natural fit, while a radiator system may need an outdoor reset control to lower the water temperature on milder days. We check the existing piping and radiators before recommending a model.

Combi, or a heat-only boiler paired with an indirect tank?

A combi boiler heats the house and your tap water in one unit, while a heat-only boiler heats the house and can feed a separate indirect water heater tank. Which suits you depends on how many bathrooms you have and how much hot water the household uses at once.

Combi boiler compared with a heat-only boiler and indirect tank
ConsiderCombi boilerHeat-only with indirect tank
SpaceOne compact unitBoiler plus a separate tank
Hot water at onceLimited by the unit’s flowA stored supply handles several fixtures
Best forSmaller homes, fewer bathroomsLarger family homes with busy mornings
Running costHeats water on demandHolds heat in the tank between uses
RepairsOne unit does both jobsTwo components, each serviced on its own

For hot water on its own, see our page on tankless water heaters in Richmond Hill.

Sizing boiler installation in Richmond Hill to the home, not the old boiler

A new boiler should be sized from a heat-loss calculation of the Richmond Hill home and the radiators or floor loops it feeds, not from the rating of the unit being removed. Richmond Hill houses change over the years, and the old boiler may have been oversized from the start.

In Richmond Hill, a finished basement, a new addition or better windows all change what the house needs. An oversized boiler cycles on and off, wastes fuel and wears out sooner, and a condensing model loses efficiency when it short cycles. We measure first, then choose the output.

Custom homes in Richvale and Bayview Hill with in-floor heat

Richvale began with modest post-war houses on generous lots, and many have been replaced by large custom homes. Some of those, and some in Bayview Hill, use a boiler for in-floor heat in basements, garages or bathrooms.

In Richmond Hill, floor loops run at low water temperatures through a mixing valve, which suits a condensing boiler well. When we replace the boiler, we check the mixing valve, the zone pumps and the loops, test any glycol in garage circuits, and make sure the new boiler works with the existing controls.

Cast iron radiators and a new boiler

Where an older home heats with radiators, cast iron radiators last a very long time and keep working with a new boiler, so replacing the boiler does not mean replacing them.

What changes is the water temperature. Radiators were designed for hot water, and a condensing boiler runs best at lower temperatures, so we check the radiators’ output, and an outdoor reset control helps by easing the water temperature as the weather warms. Some rooms may need a larger radiator.

Venting changes when a condensing boiler goes in

A condensing boiler’s exhaust is cool and wet, so it cannot use an old masonry chimney in the usual way. It vents through sealed PVC or polypropylene pipe, as the maker specifies, usually through a side wall.

That changes the plan for older Richmond Hill homes. We check where the vent can exit, how far it can run, where the combustion air comes from and where the condensate drain goes. If an old chimney was shared with a water heater, that appliance may need its own venting, and we plan for it.

Piping, air removal and controls around the boiler

A good boiler installation in Richmond Hill includes the piping and controls around the boiler, because those decide how it behaves for years. Poor piping can cause noise, air in the system, uneven heat and early failure of a new boiler.

  • Near-boiler piping set up as the maker specifies, often a primary and secondary loop
  • An air separator and automatic vents so trapped air leaves the system
  • A correctly sized expansion tank and a pressure relief valve
  • Circulator pumps and zone valves checked or replaced where they are tired
  • Outdoor reset and zone controls set up for how you use each area

Flushing and treating old system water protects the new boiler from sludge.

Boiler installation in Richmond Hill, from shutdown to first fire

A boiler replacement in Richmond Hill takes longer than an air conditioner swap, and the time depends on the piping and venting. We confirm a two-hour arrival window when you book and text you when the technician is on the way, and we do not promise a finish time.

The crew shuts down and drains the system, removes the old boiler, sets the new one, connects gas, water, venting and condensate, refills and purges the loops, and sets the controls. Then they fire the boiler, test the safeties and walk you through the settings. We handle the permits and inspections the job needs.

Gas safety and licensed work

Gas appliance work in Richmond Hill, as across Ontario, must be done by a qualified, certified technician, and ours are TSSA-certified. They test for gas leaks, check venting and carbon monoxide levels, and confirm the safety controls work before they leave.

Ontario law has required CO alarms on every storey since January 1, 2026, on top of one next to each sleeping area, wherever a home has a fuel-burning appliance, a fireplace or an attached garage, so check yours when a boiler goes in. See the Ontario carbon monoxide safety page (opens in a new tab) for placement. If you smell gas, leave the house and call Enbridge Gas at 1-866-763-5427 from outside. If a carbon monoxide alarm sounds, everyone should go outside and then call 911.

What goes into boiler installation cost in Richmond Hill

The price of a new boiler in Richmond Hill depends on its type and size, what is being replaced and how much piping, venting and control work the house needs. We quote a flat-rate price after a site visit, and you approve it before any work begins.

What affects the cost of a boiler replacement
What affects itWhy it matters
TypeA combi, a heat-only boiler or a boiler with an indirect tank
CapacitySet by the heat-loss calculation
EfficiencyCondensing models cost more and use less fuel
VentingA new sealed vent route and condensate drain add work
Piping and controlsNear-boiler piping, air separation, reset and zone controls
Old system conditionFlushing, pumps and valves that need replacing

Yearly service for the new boiler

A new boiler lasts longest in Richmond Hill with a yearly service. A visit cleans the burner and heat exchanger, checks the condensate drain and neutralizer, tests the safety controls and pressure and looks at pumps and valves.

Our maintenance plan includes two visits a year and priority booking. Many manufacturer warranties ask for proof of regular maintenance, so check your warranty papers.

FAQ

Boiler installation questions from Richmond Hill homeowners

How many years should a boiler give us?

It varies by type, installation and water quality, but a well-maintained boiler often runs for many years, and cast iron radiators can outlast several boilers. We judge a boiler by its condition, leaks and repair history, not by age alone, and we tell you honestly whether repair or replacement is the better spend.

Do I need to replace my radiators with a new boiler?

No. Cast iron radiators keep working with a new boiler. What changes is the water temperature, since a condensing boiler runs best at lower temperatures. We check each radiator’s output and may add an outdoor reset control, and in a few rooms a larger radiator could be worth discussing.

Is a condensing boiler worth it for in-floor heat?

Often, yes. In-floor loops run at low water temperatures, which lets a condensing boiler recover heat from its exhaust and reach efficiency of 90 percent AFUE or better. We check the mixing valve, pumps and loops first, so the boiler and the floors work together.

Can a combi boiler heat a large two-storey house?

It can heat it, but hot water is the limit. A combi heats tap water on demand, so several showers at once can exceed what it delivers. A heat-only boiler with an indirect tank suits larger households. We ask how many bathrooms you have and how you use hot water before recommending either.

Do you install boilers in Bayview Hill and Richvale?

Yes. Boiler installation in Richmond Hill covers the whole city, including Bayview Hill, Richvale, Mill Pond, North Richvale, Oak Ridges and Jefferson. Send a request and we call back to book a two-hour arrival window, then text you when the technician is on the way.

Can my old chimney vent a new condensing boiler?

Not in the usual way. In Richmond Hill, condensing boilers produce cool, wet exhaust and vent through sealed PVC or polypropylene pipe, usually out a side wall, as the maker specifies. We plan the vent route, the combustion air and the condensate drain during the site visit, and we handle the permits and inspections.

What happens to the old boiler?

In Richmond Hill, we drain and disconnect it, carry it out and take it away. The old system water is handled properly, and the loops are flushed so sludge does not damage the new boiler. You do not need to arrange removal, and it is part of the flat-rate price you approve before work starts.

Is boiler work covered by a warranty?

Every installation we do carries a written workmanship warranty, and the boiler itself comes with the manufacturer’s own warranty. Keep your paperwork and ask us how to register it. Our technicians are TSSA-certified, WSIB covered and insured, and you see the flat-rate price before work starts.

Book a visit

Need boiler installation in Richmond Hill? We’ll call you back to book.

Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.

(647) 905-9241

Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies

Get an installation quote

Tell us about your home. We’ll call to book a quote visit.

What do you need?
How soon? Optional
Add an email or detailsOptional

Or call (647) 905-9241Used only to book your visit. Privacy