
Radiators not heating can mean one stubborn radiator or a whole house gone cold, and the pattern tells you where to look. Trapped air, a stuck valve, sludge, low pressure and a failed pump are the usual causes, and a few of them you can check in minutes. This guide sorts the causes by symptom and says when to book boiler repair.
Key takeaways
- Where the cold is, whether at the top, the bottom or the whole house, points to the cause.
- Trapped air, a stuck valve, sludge and low pressure are common causes.
- You can check the thermostat, the gauge and the radiator valves, and bleed with the system cool.
- A cold house with a boiler that won’t fire is a gas technician’s job.
- Gas smell or a carbon monoxide alarm comes first. Leave and call.
Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.
On this page
- Why radiators stay cold when the boiler is on
- First checks for radiators not heating
- One radiator not heating while the rest are fine
- A radiator cold at the top: trapped air
- Radiators cold at the bottom or in the middle: sludge
- Upstairs or far radiators not heating up
- Radiators not heating anywhere: boiler, pump or zone fault
- Radiators not heating after bleeding
- Gas smells and carbon monoxide with a gas boiler
- What a technician checks on a cold-radiator call
- Keeping radiators heating all winter
- Radiators not heating: common questions
Why radiators stay cold when the boiler is on
A hot water radiator heats only when the boiler makes hot water, the pump moves it and nothing blocks its way into the radiator. When any of those three steps fails, you get radiators not heating even though the boiler seems to be running. Each cause leaves its own pattern of cold.
Start by deciding what kind of cold you have. One radiator, one floor, the top of a radiator, the middle or the whole house each point somewhere different, and the table below puts the common patterns in one place.
| What you notice | Likely cause | Who fixes it |
|---|---|---|
| Hot at the bottom, cold at the top | Air trapped in the radiator | You, by bleeding with the system off and cool |
| Cold at the bottom, hot at the top | Sludge or a restriction at the bottom | Technician |
| Cold in the middle, hot at the edges | Sludge building up inside | Technician |
| One radiator cold, others hot | Stuck valve or a blocked radiator | You check the valve, then a technician |
| Upstairs cold, downstairs warm | Air, low pressure or poor balance | You check the gauge, then a technician |
| Whole house cold | No heat from the boiler, pump or zone fault | Technician |
First checks for radiators not heating
Before you look at any radiator, confirm that the system is actually calling for heat. A thermostat on the wrong mode or a tripped breaker can leave every radiator cold. Those checks take a couple of minutes and need no tools.
- Thermostat: set to Heat, with the setpoint above the room temperature, and new batteries if it takes them.
- Breaker: if the boiler’s breaker has tripped, reset it once. If it trips again, leave it off and call.
- Boiler power: check that the boiler’s display is lit and its switch is on.
- Gauge: read the pressure gauge and compare it with your normal reading.
- Hot water: if you have a combi boiler, see whether the taps run hot.
If none of that explains it, move to the pattern of the cold, starting with a single radiator.
One radiator not heating while the rest are fine
One cold radiator in a warm house is usually a local problem: a closed or stuck valve, air trapped inside, or a blockage in that radiator. The boiler and pump are clearly working, since the others heat. That makes this the easiest pattern to deal with.
Check by hand that the radiator’s handwheel valve is open. Leave the capped lockshield valve at the other end alone, since it sets the balance. If the handle turns freely but the radiator stays cold, the valve pin may be stuck, and a technician can free or replace it. Don’t force anything with a wrench.
A radiator cold at the top: trapped air
A radiator that is hot at the bottom and cold at the top has air trapped in the upper part. Air is lighter than water, so it rises and sits where the hot water should be. Bleeding the radiator lets it out, and the radiator then fills and heats the whole way up.
The method is short, but the safety steps matter: system off and cool, a radiator key, a cloth, and the screw closed the moment water appears. Our guide on how to bleed a radiator has each step. Steam radiators are different, so don’t bleed those.
Radiators cold at the bottom or in the middle: sludge
A radiator that is cold at the bottom or in the middle, with heat only around the edges, often has sludge inside. Sludge is a mix of rust and mineral debris that settles in low points and narrows the passages water has to flow through.
It builds slowly in older systems, and cast iron radiators in older homes are common culprits. Bleeding does not help, and chemicals are not a homeowner job. A technician can test the water and flush the radiator or the system, then protect it from building up again.
Upstairs or far radiators not heating up
When the radiators farthest from the boiler, or those on the top floor, are the cold ones, the system may be short of water pressure or out of balance. Hot water takes the easiest path, so the nearest radiators can take most of the flow and leave the far ones lukewarm.
Look at the pressure gauge first. If the reading is low, see our guide to boiler pressure. Balancing the radiators means setting the lockshield valves on each so the flow is shared, and a technician does it with the right tools.
Radiators not heating anywhere: boiler, pump or zone fault
If every radiator is cold, the problem sits upstream of them: the boiler is not making heat, the pump is not moving it, or a zone valve is not opening. A boiler that is on and humming but not heating points to the pump or a zone. A boiler that won’t light points to a gas or control fault.
These are technician repairs. A circulator pump that hums but doesn’t turn, a zone valve stuck shut and a boiler that locks out all need testing with the right gear. Keep the boiler’s covers closed, and don’t reset it over and over.
- Pump: the pipes near it stay cold, or it hums without moving water
- Zone valve: one zone is cold while another is fine
- Boiler: it won’t light, locks out or shows a fault on its display
- Pressure: the gauge is near zero, so the boiler won’t fire
The code list for a fault is usually on a label inside the panel or in the manual, and the technician reads it on site.
Radiators not heating after bleeding
Bleeding sometimes makes things worse for a while, because letting out air also lets out a little water, and the pressure can fall below what the boiler needs. If your radiators went cold after you bled one, look at the gauge first.
If the pressure is low, topping it up is allowed only when the manual for your boiler spells out the steps. No steps, no top-up: call. If the pressure holds and a radiator is still cold, air may remain, and a second bleed after the system cools is fair.
Gas smells and carbon monoxide with a gas boiler
Cold radiators are a repair job, yet two warning signs turn any boiler problem into an emergency. Smelling gas means walking out right away, with no switches flipped and no phone used indoors. Once you are outside, Enbridge Gas takes the call on 1-866-763-5427.
The second sign is a carbon monoxide alarm that sounds. Everybody, pets too, goes outdoors, and 911 gets the call. The province requires CO alarms next to every sleeping area and, since January 1, 2026, on every storey of any home with a fuel-burning appliance, a fireplace or an attached garage, as the Ontario carbon monoxide safety page (opens in a new tab) lays out.
What a technician checks on a cold-radiator call
The technician begins with the pattern you describe, then tests from the boiler outward. The aim is to find out whether heat is being made, moved and delivered, and to fix the first step that fails. Having the gauge photo and the cold rooms noted saves time.
- Reads the pressure and checks the expansion tank and filling valve
- Tests that the boiler fires and holds a steady flame
- Checks the circulator pump and each zone valve
- Feels along the pipes to find where the heat stops
- Looks at the radiator valves, then bleeds or flushes as needed
Nothing gets repaired until you agree to the flat-rate price. A no-heat call is answered around the clock, and a scheduled visit comes with a two-hour window plus a text as the technician heads over.
Keeping radiators heating all winter
Most cold-radiator problems build slowly, so a little attention in the fall helps. Bleed the radiators at the start of the season, read the gauge now and then, and keep furniture and curtains off the radiators so heat can leave them.
A yearly service tests the pump, valves and pressure before the cold arrives. The maintenance plan includes a yearly boiler service before the heating season. Neighbours in the north can look at boiler repair in Richmond Hill, or get in touch to book.
Radiators not heating: common questions
Why are my radiators not heating up but the boiler is on?
The boiler may be making heat that isn’t reaching the radiators. Trapped air, a stuck valve, sludge, low pressure, a failed pump or a closed zone valve can all stop hot water getting there. Check the thermostat and the gauge, then look at where the cold is for clues.
Why is my radiator hot at the bottom and cold at the top?
Air has collected in the upper part of the radiator. Air rises above the water and blocks the heat. Bleed the radiator with the heating off and cool, using a radiator key and a cloth, and close the screw as soon as water appears.
Why is my radiator cold at the bottom?
A radiator cold at the bottom and hot at the top usually has sludge or a restriction low down. Rust and debris settle there and narrow the flow. Bleeding won’t help. A technician can test the water and flush the radiator or the system.
Why is only one radiator cold?
It’s usually local: a closed or stuck valve, air trapped inside or a blockage in that radiator. Check that its valves are open by hand, and bleed it if it’s cold at the top. If that doesn’t work, a technician can free the valve or flush it.
Why are my upstairs radiators cold?
The top floor is first to suffer from air, low pressure or an unbalanced system. Read the pressure gauge, and bleed upstairs radiators with the system cool. If the pressure is normal and they stay cold, the radiators need balancing, which is a technician’s job.
Should I flush my radiators myself?
No. Flushing involves draining the system, handling dirty water and often chemicals, and it can leave the boiler with air or low pressure. A technician has the tools to do it properly and to test whether sludge is the cause first.
Can a boiler heat the water but not the radiators?
Yes. With a combi boiler, the taps can run hot while the radiators stay cold if the diverter valve inside the boiler, a zone valve or the heating circuit has a fault. If the radiators are cold but the water is hot, book a technician to test the heating side.
Who fixes cold radiators in the GTA?
Assurance HVAC Heating & Cooling sends TSSA-certified gas technicians to homes in Mississauga, Oakville, Vaughan, Richmond Hill, Markham, North York and Toronto. The price is set and agreed by you ahead of the work, and the repair is backed by a written workmanship warranty. The line is staffed 24/7.
Still no heat? We’ll call you back to book a technician.
Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.
Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies
