
A thermostat not working can mean a blank screen, a screen that lights up but never starts the furnace, or a reading that is plainly wrong. Often the cause is simple: dead batteries, the wrong mode or no power to the furnace. This guide walks through the checks that are safe to do yourself, explains what points to a wiring or equipment fault, and shows when to book furnace repair.
Key takeaways
- Dead batteries, the wrong mode and a tripped breaker cause many thermostat problems.
- A blank screen on a thermostat with no batteries often means the furnace has lost power.
- You can check settings, batteries, the breaker and the furnace service switch.
- Wiring, transformer and control faults are technician work, and so is opening the furnace.
- Book a visit if the thermostat has power but heating or cooling never starts.
Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.
On this page
- What your thermostat does, and what it does not
- Thermostat not working: symptoms and likely causes
- Start with mode, setpoint and schedule
- Replace the batteries in a thermostat
- Check the power to the furnace and thermostat
- What you can look at, and what to leave alone
- A thermostat reading the wrong temperature
- Cooling not starting from the thermostat
- Smart and programmable thermostats go wrong differently
- When a thermostat not working needs a technician
- Thermostat not working in winter: when the heat will not start
- Gas and carbon monoxide safety
- Thermostat not working: common questions
What your thermostat does, and what it does not
A thermostat is a switch that reads the room temperature and sends a signal when heating or cooling should start. It does not make heat itself. When a thermostat is not working, the fault can be in the thermostat, in the low-voltage wires behind it, or in the furnace or air conditioner receiving the signal.
That is why the checks below work from the simplest cause to the most involved.
Thermostat not working: symptoms and likely causes
What the screen shows says a lot about where the problem sits. A dead screen usually points to batteries or power. A working screen with no response points toward the wiring or the equipment. The table matches the common symptoms with their usual causes and who handles them.
| What you notice | Likely cause | Who fixes it |
|---|---|---|
| Screen is blank | Dead batteries, or the furnace has no power | You first (batteries, switch, breaker) |
| Screen is on, but nothing starts | Wrong mode, a hold or schedule, or a fault in the equipment | You first (mode, setpoint), then a technician |
| Heat works but cooling does not, or the reverse | Mode setting, or a fault in one system | You first (mode), then a technician |
| Temperature reading looks wrong | Poor location, sun, a draft, or a failing sensor | You first (location), then a technician |
| Furnace runs without stopping | Fan set to On, or a stuck relay or control | You first (fan setting), then a technician |
| Smart thermostat shows offline or restarts | Weak Wi-Fi, or not enough power from the wiring | You first (Wi-Fi), then a technician |
Start with mode, setpoint and schedule
Many cases of a thermostat not working are a setting. Check that the mode is on Heat in winter or Cool in summer, that the setpoint is a few degrees above or below the room temperature, and that no hold or schedule is overriding what you want. It takes under a minute.
- Mode: Heat or Cool, not Off or a blank setting.
- Setpoint: at least three degrees above room temperature for heat, or below it for cooling.
- Hold or schedule: cancel a temporary hold, and check the schedule is on the right day and time.
- Fan: set to Auto unless you want the fan to run constantly.
- Lock or keypad icon: some models lock the screen, and the manual explains how to unlock it.
Replace the batteries in a thermostat
Fresh batteries fix many a thermostat not working. Many models run on two AA or AAA batteries, and when they weaken the screen dims, goes blank, or the thermostat stops calling for heat. Replace both with new ones of the same type, and put them in the way the markings inside show.
Some models show a low battery warning and some do not. If yours has a battery compartment and has not been changed in a year or two, change them even if the screen still works.
Check the power to the furnace and thermostat
A thermostat that is wired to the furnace for power goes blank when the furnace loses power. Check the furnace service switch, which looks like a light switch on or near the furnace, and make sure it is on. Then check the breaker, and reset it once if it has tripped.
- Furnace service switch: flip it off, wait about 30 seconds, then switch it back on.
- Breaker: if tripped, push it fully off, then on, one time only.
- If the breaker trips again, leave it off and call.
- Never open the furnace door or the electrical box, or take the cover off the breaker panel.
A furnace with no power usually has a plain cause. Our furnace not turning on guide covers the checks after the thermostat.
What you can look at, and what to leave alone
If the thermostat has power but nothing happens, the next suspect is the low-voltage wiring, and that is where homeowner checks end. You can look, but not fix. If your thermostat’s faceplate lifts off its base the way the manual describes, you can photograph the letters beside each wire, but don’t loosen, move or reconnect anything. If it controls electric baseboard heaters, it runs on household voltage, so don’t open it at all.
- You can read the letters beside the wire terminals and take a photo for the technician.
- Do not unscrew, reconnect, swap or jump any wires.
- Do not touch the furnace control board or its fuse.
- Do not open the furnace to check its connections.
A loose wire, a blown low-voltage fuse or a weak transformer can all stop a thermostat from working, and a technician tests them safely. Our smart thermostat C-wire guide explains the wire that powers many new models.
A thermostat reading the wrong temperature
A thermostat that seems to be working but reads wrong is often in the wrong spot. Sun on the wall, a lamp or TV nearby, a supply register blowing at it, or a cold exterior wall all push the reading away from the room’s real temperature, so the furnace stops early or runs too long.
- Look for sun, lamps, appliances or a register close to the thermostat.
- Check that the wall around it has no draft from a hole or gap.
- Move the sun or heat source, rather than the thermostat.
- Moving a thermostat means rewiring, which is a technician’s job.
Cooling not starting from the thermostat
If the heat works but cooling does not, check that the thermostat is in Cool mode with the setpoint below the room temperature. Many systems have a float switch that shuts the air conditioner off when the condensate pan or drain backs up, so look at the pan and drain for water or a visible clog.
If both checks are fine and the outdoor unit stays silent, a technician finds the cause. Our AC repair page explains the usual faults.
Smart and programmable thermostats go wrong differently
A smart or programmable thermostat has more that can fail than a plain dial. A schedule can override your setpoint, a Wi-Fi drop can make a smart model look broken, and a model that is short of power can restart or lose its settings. Check the app, the Wi-Fi and the manual first.
A restart in the middle of a heating cycle often means too little power from the wiring. A technician can check this, and we install and set up smart thermostats through our indoor air quality and thermostat service.
When a thermostat not working needs a technician
Call when the thermostat has power and the right settings, but the furnace or air conditioner never starts. That points to wiring, a safety control or the equipment itself, none of which are safe homeowner jobs. A technician tests the signal at the thermostat and at the equipment to find where it stops.
You approve a flat-rate price before any work starts, and repairs carry our written workmanship warranty.
Thermostat not working in winter: when the heat will not start
A thermostat not working in winter can become a no-heat emergency quickly. If the house is cooling and the checks above have not helped, call. Our emergency line is open 24/7, and technicians go out day or night. While you wait, keep everyone warm and see our no heat in the house guide.
Gas and carbon monoxide safety
Troubleshooting a thermostat should never involve taking a risk with gas equipment. Any Ontario home with an attached garage, a fireplace or a fuel-burning appliance must have CO alarms next to the sleeping areas and, as of January 1, 2026, on every storey, and the province’s carbon monoxide safety page (opens in a new tab) explains where they go.
- CO alarm sounding: get everyone, pets included, outside and call 911.
- Gas smell: leave the house without touching switches or phones, then call Enbridge Gas at 1-866-763-5427 from outside.
Thermostat not working: common questions
Why is my thermostat screen blank?
Usually the batteries are dead, or the furnace has lost power. Replace the batteries first. Then check that the furnace service switch is on and the breaker has not tripped, resetting it once at most. A screen that stays blank after that needs a technician to check the wiring and transformer.
Why won’t my thermostat turn on the heat?
Check that it is in Heat mode with the setpoint a few degrees above the room temperature, and that no hold or schedule overrides it. Then check the batteries, the furnace service switch and the breaker. If everything looks right, the furnace or its controls need a technician.
How often should thermostat batteries be changed?
About once a year is a common rule, and sooner if the screen dims or the thermostat stops calling for heat. Some models warn when batteries are low and some do not. Use new batteries of the same type, and replace all of them at once.
Can I fix thermostat wiring myself?
No. If the faceplate lifts off as the manual describes, you can look at the labels beside the wires and take a photo, but loosening, moving or reconnecting them is a job for a technician. A wrong connection can damage the thermostat or the equipment, and the furnace itself should never be opened by a homeowner.
Why does my thermostat show the wrong temperature?
Sun, a lamp, a register or a draft near the thermostat often skew the reading. Remove the source if you can. If the reading is still wrong, the sensor may be failing, and a technician can test and replace the thermostat. Moving it needs rewiring.
Why does my furnace keep running when the thermostat says it should stop?
Check that the fan setting is on Auto and not On, since On keeps the blower running. If the burners keep firing after the thermostat is satisfied or set to Off, switch the furnace off at its service switch and call, because a control or gas valve may be stuck. A fan that runs constantly on Auto usually means a relay fault.
Is a new thermostat worth it if the old one still works?
Only if it solves a problem. A newer model can offer schedules, remote control and humidity features, but it will not fix a furnace fault. Check the model works with your system, and have it installed properly, so it gets enough power from the wiring.
Who can repair a thermostat or install a new one in the GTA?
Our technicians test, replace and set up thermostats across Toronto, North York, Richmond Hill, Vaughan, Markham, Mississauga and Oakville. Booked visits get a two-hour arrival window and a text, and you approve a flat-rate price before any work starts. We are open 24/7 for no-heat calls.
Want a technician to take a look? We’ll call you back to book.
Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.
Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies
