
Assurance HVAC Heating & Cooling does A.O. Smith water heater repair across Toronto and the GTA, from atmospheric gas tanks to power vent, direct vent and condensing tankless models. Our TSSA-certified gas technicians diagnose first and quote a flat-rate price you approve before any work begins. If the tank is past saving, we also handle water heater installation.
Key takeaways
- Our technicians work on A.O. Smith gas tank, power vent, direct vent and tankless units.
- Serving Toronto and the GTA, with TSSA-certified gas technicians on gas water heaters.
- You approve a flat-rate price before any repair work starts.
- Open 24/7, with technicians out day or night when the hot water is gone.
- Anode checks and tank flushes are the low-cost repairs that can add years to a gas tank.
Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.
On this page
- A. O. Smith in brief: the maker and its Canadian range
- Atmospheric, power vent or direct vent: why the vent type shapes the repair
- Common A.O. Smith water heater repair jobs on gas tanks
- A.O. Smith water heater flashing light codes
- Condensing tankless repair and scale prevention
- Anode rods: the low-cost insurance inside the tank
- What to check before you call
- Model, serial number and the warranty validation tool
- A.O. Smith water heater repair or replacement: how to choose
- Owning or renting a water heater: how to decide
- Leaks, gas smell and carbon monoxide
- A.O. Smith water heater repair visits, and where we work
- A.O. Smith water heater repair questions
A. O. Smith in brief: the maker and its Canadian range
A. O. Smith says it has been innovating since 1874, is headquartered in Ashland City, Tennessee, and built its first residential water heater in 1939. A. O. Smith’s Canadian site is run by A. O. Smith Enterprises Ltd., with an office in Fergus, Ontario. We are an independent contractor and not affiliated with the company.
The Canadian residential site sorts the range into gas, high-efficiency gas, tankless and electric. Knowing which family your heater belongs to tells a technician where to start looking when the hot water stops.
Atmospheric, power vent or direct vent: why the vent type shapes the repair
On a gas tank, the way it vents decides which parts can fail and how we test them. A. O. Smith’s Canadian site lists atmospheric vent lines, a power vent line and sealed-combustion direct vent lines, and each one fails in its own way.
- ProLine and ProLine Master are listed as atmospheric vent, so combustion air and exhaust move by natural draft
- ProLine XE is listed as atmospheric with a flue damper, which adds a moving part to check
- The power vent line uses a blower, so a blower or pressure problem can keep the burner from lighting
- ProLine XE Power Direct Vent has a sealed combustion chamber and an “ultra quiet blower” per the maker
- ProLine Direct Vent has what the maker calls a balanced flue design
Common A.O. Smith water heater repair jobs on gas tanks
Most gas tank calls come down to a short list: a thermocouple or flame sensor that no longer proves the flame, a failed gas valve, a weak igniter, a clogged vent, or a tank full of sediment. We test in order, so you pay to fix the part that actually failed.
Pilot or burner will not stay lit
A thermocouple or flame sensor that has worn out will shut the gas off a few seconds after ignition. Replacing it is a routine repair. If the gas valve itself is not responding, it is replaced as an assembly.
Rumbling, popping and slow recovery
Sediment settles at the bottom of the tank and traps heat against the steel. A flush clears it, though a tank with heavy buildup may not recover fully. That is a good moment to weigh repair against replacement, and our maintenance plan can include your water heater alongside the furnace and AC.
Vent and blower faults
Power vent and direct vent models shut down when the exhaust path is blocked or the blower is not proving airflow. We check the blower, the pressure switch and the vent run before touching the gas train.
A.O. Smith water heater flashing light codes
These codes are from A. O. Smith’s Canadian installation instructions and use and care guide for its ProLine and ProLine Master atmospheric vent gas tanks. The status light on the gas control valve gives a code by the number of flashes. After the pilot is lit, it can take up to 90 seconds before the light starts to blink.
The chart is on pages 32 and 33 of A. O. Smith’s Canadian ProLine manual (opens in a new tab).
| Code | What it means | What to do |
|---|---|---|
| 0 flashes (light not lit) | Pilot is not lit, or the thermopile has not yet reached normal operating temperature | Turn the knob to OFF, wait 10 minutes, then relight using the label on the heater. If it will not light, book a repair |
| Light on (solid) | Pilot went out recently and the thermopile is cooling down | Wait 10 minutes before relighting |
| 1 flash (every 3 seconds) | Normal operation | Nothing |
| 2 flashes | Pilot is lit, but the thermopile is not producing the voltage the valve needs | Book a repair |
| 4 flashes | Water temperature got too high, so the main burner and pilot were shut off | Turn the knob to OFF and book a repair |
| 5 flashes | The temperature sensor (thermistor) is defective | Turn the knob to OFF and book a repair |
| 7 flashes | Gas control valve failure | Turn the knob to OFF, close the gas supply to the heater and book a repair |
| 8 flashes | Knob is off but the thermopile still makes power: it has not cooled yet, or the pilot valve is stuck open | Leave the knob at OFF and call a technician |
Count the flashes twice to be sure, then call. Our TSSA-certified gas technicians confirm the code and test the gas valve, thermopile or sensor it points to before replacing anything.
Condensing tankless repair and scale prevention
A. O. Smith’s Canadian gas tankless lines are condensing: the Adapt+ Premium with an integrated recirculation pump, and the Adapt SC Standard. Both are listed with X3 Scale Prevention Technology, which is the maker’s answer to mineral buildup in hard water.
Scale prevention is not the same as no maintenance. We still inspect the heat exchanger, check the condensate drain and flush the unit when water hardness calls for it.
Anode rods: the low-cost insurance inside the tank
An anode rod is a sacrificial metal rod that corrodes so the steel tank does not. Once it is used up, the tank itself starts to rust. Replacing a worn anode is far cheaper than replacing a tank, and it is one of the few repairs that can add years.
A. O. Smith’s Canadian site lists powered anode rods as an accessory on its electric range. We can look at your anode during a visit and tell you how much of it is left.
What to check before you call
Three quick checks sort out a surprising number of no-hot-water calls. They take a few minutes, need no tools and are safe if you stay away from anything that smells like gas.
- Is the thermostat dial on the gas valve still set where it was, and is the gas supply valve open?
- On a power vent or power direct vent model, is the unit plugged in and is the breaker on?
- Are other hot taps cold too, or only one fixture? A single cold tap points at a mixing valve, not the heater
- Is there water around the base of the tank? If so, go to the safety section below
If the pilot will not relight after one attempt, stop. Repeated attempts do not help and a gas smell means leave the house.
Model, serial number and the warranty validation tool
Keep your model and serial number with your purchase paperwork. A. O. Smith’s Canadian site offers a warranty validation tool, and it is where homeowners should check their coverage, since we do not state warranty terms for the maker.
We have no sourced method for dating an A. O. Smith unit from its serial number, so your install paperwork is the better record of age. If a repair may fall under the maker’s coverage, we will say so.
A.O. Smith water heater repair or replacement: how to choose
Repair makes sense when the tank is sound and the failed part is small. Replacement makes sense when the steel is leaking, since that cannot be fixed. Age matters too: a gas tank typically lasts 8 to 12 years and a tankless unit about 20 years.
| Problem | Usual answer | Why |
|---|---|---|
| Thermocouple, flame sensor or igniter | Repair | Small part, tank is unaffected |
| Gas valve on a young tank | Repair | Cost is reasonable if the tank is sound |
| Worn anode, tank under 10 years | Repair | Can slow corrosion |
| Leak from the tank body | Replace | A leaking tank cannot be patched |
| Tank over 10 years with sediment and rust | Usually replace | More failures follow |
| Tankless with scale and no recent flush | Descale first | Often restores flow |
Owning or renting a water heater: how to decide
Whether to own or rent depends on how long you will stay, how you feel about paying a monthly amount, and who handles repairs. Owning means one purchase and your own choice of repair company. We make no claims about any rental company, so compare the terms you have in writing.
Leaks, gas smell and carbon monoxide
If water is leaking from the tank, close the cold water valve on top of the tank, turn the gas control to pilot or off, and call us. If you smell gas, leave the house and call Enbridge Gas at 1-866-763-5427 from outside.
If a carbon monoxide alarm sounds, get everyone outside and call 911. A gas water heater is a fuel-burning appliance, and Ontario requires CO alarms next to each sleeping area and, since January 1, 2026, on every storey of homes with one, a fireplace or an attached garage. More at Enbridge Gas safety (opens in a new tab).
A.O. Smith water heater repair visits, and where we work
Booked visits come with a two-hour arrival window and a text before we arrive. We diagnose, explain what failed and give a flat-rate price. Nothing starts until you approve it, and repairs carry our written workmanship warranty.
We cover Toronto, North York, Richmond Hill, Vaughan, Markham, Mississauga and Oakville. See our Toronto area page for local details. No hot water at night or on a weekend? We are open 24/7, and you can request a visit any time.
Assurance HVAC Heating & Cooling is an independent HVAC contractor, not affiliated with or authorized by A.O. Smith. Brand names are trademarks of their owners.
A.O. Smith water heater repair questions
Why does my A.O. Smith pilot keep going out?
The usual cause is a worn thermocouple or flame sensor that no longer proves the flame, so the gas valve shuts off. A blocked vent or draft problem can also blow the flame out. Relighting over and over will not fix it, so book a technician to test the parts in order.
Do you repair A.O. Smith tankless water heaters?
Yes. Our technicians work on condensing tankless units, including flushing scale from the heat exchanger and checking the condensate drain and venting. We do not interpret a specific error code from memory. We read what the unit reports on site, then test the part it points to.
Can I remove the anode rod to stop the rotten egg smell?
Do not remove it permanently. A tank without an anode corrodes faster, and A. O. Smith’s own anode guidance is not on the pages we reviewed, so check your warranty papers first. A technician can deal with a smell, often through a different rod or a flush.
What does it mean when my A.O. Smith water heater flashes 7 times?
On ProLine and ProLine Master atmospheric vent tanks, A. O. Smith’s Canadian manual says 7 flashes means gas control valve failure. Its steps are to turn the knob to OFF, turn the main gas supply off and replace the gas control valve, which is technician work. Book a repair, and do not keep relighting it.
Does a power vent model need electricity to heat water?
Yes. A power vent or power direct vent model uses a blower, so a power cut or tripped breaker stops the burner even though gas is flowing. Check that it is plugged in and the breaker is on. If the blower runs but the burner does not fire, a technician should look.
How do I check my A.O. Smith warranty?
A. O. Smith’s Canadian site has a warranty validation tool, and the maker is the only source for coverage terms. Have your model and serial number ready, plus the install date. We can tell you what failed, but we cannot speak for the maker on what is covered.
Is a flush worth doing on an older tank?
Often yes, if the tank is not leaking. Flushing removes sediment that causes rumbling and slow recovery, and a technician can check the anode at the same time. If the tank is badly scaled or rusting, we will tell you plainly that replacement is the better spend.
Need A.O. Smith water heater repair? We’ll call you back to book.
Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.
Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies
