Skip to content
Water heater tank in an unfinished basement
Homeowner guides

How to flush a water heater, step by step

(647) 692-0819Open 24/7, day or night

Knowing how to flush a water heater is one of the few tank jobs a homeowner can do safely, and it clears the sediment that makes tanks rumble, run out and wear out. It only takes a hose and some patience, but the order of the steps matters, and some tanks shouldn’t be flushed at all. This guide covers both, and when to book water heater repair instead.

Request a technician

Tell us what’s going on. We’ll call to confirm a time.

What do you need?
How soon? Optional
Add email, details or text updatesOptional

Or call (647) 692-0819Used only to book your visit. Privacy

Key takeaways

  • Flush only with the gas control set to off or the power switched off, after the tank cools.
  • Hose the drain valve to a floor drain, and open a hot tap to let air in.
  • Stop if the drain valve is brittle, leaks or won’t close, and call a technician.
  • On an electric tank, refill completely before the power goes back on.
  • Don’t remove an anode rod or touch the relief valve beyond what the manual asks.

Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.

On this page
  1. How to flush a water heater, and why it helps
  2. How often to flush a tank water heater
  3. Before you start: what you need and when not to flush
  4. How to flush a water heater: the steps
  5. Restarting a gas or electric tank after the flush
  6. When to stop and call a technician
  7. How to flush a water heater: what not to do
  8. Flushing for noise, short supply and smells
  9. Gas, carbon monoxide and scald safety while flushing
  10. What a technician does that a homeowner flush can’t
  11. Making a flush part of the routine
  12. How to flush a water heater: common questions

How to flush a water heater, and why it helps

A flush drains sediment, mostly mineral scale from hard water, out of the bottom of a tank. Left in place, that layer insulates the water from the burner or element, causes popping and rumbling, takes up space and can shorten the tank’s life. Hard water is common in the GTA, so sediment builds steadily.

  • Fewer rumbling, popping and banging noises
  • More hot water available from the same tank
  • Less strain on the burner or lower element
  • A chance to see how much sediment the tank is making

How often to flush a tank water heater

Many makers suggest a flush about once a year, and a tank in hard water may benefit from more often. Check your manual, which gives the interval for your model. A tank that has never been flushed and is many years old is a special case, covered below.

Before you start: what you need and when not to flush

Gather the right gear first and check that your tank is suitable. You need a garden hose long enough to reach a floor drain, a bucket and old towels. Some tanks shouldn’t be flushed by a homeowner, and the list below shows when to leave it alone.

  • You need a garden hose, a bucket, towels and about an hour.
  • Skip the flush if the tank is already leaking: close the cold water valve on top, turn the gas control to off or switch off the breaker, and call.
  • Skip it if the tank is very old and has never been flushed. Disturbing old sediment can leave a drain valve that won’t close.
  • Skip it if the drain valve is plastic and brittle, or if you can’t reach a floor drain with the hose.
  • A tankless unit isn’t flushed this way. See our tankless descaling guide.

How to flush a water heater: the steps

These steps work for most tanks with a drain valve near the bottom. Work in order, and don’t skip the cooling time, because the water in a tank can scald. If anything doesn’t go as described, stop and call.

  • Turn the gas control to off, or switch off the water heater’s breaker. Never flush with the heat on.
  • Wait for the tank to cool, several hours or overnight if it was recently heating.
  • Close the cold water valve on top of the tank.
  • Connect a garden hose to the drain valve and run it to a floor drain.
  • Open a hot water tap upstairs so air can enter and the tank drains.
  • Open the drain valve slowly and let the tank drain fully.
  • Briefly open the cold water valve with the drain open to stir up and wash out what’s left, then close it.
  • Close the drain valve snugly without forcing it, remove the hose, and open the cold water valve again.
  • Leave the hot tap open until water flows steadily, then close it.

Restarting a gas or electric tank after the flush

Don’t rush the restart, because heating an empty or partly filled tank can damage it. The tank must be completely full first. On an electric tank, an element that heats without water burns out within minutes, so the breaker stays off until water runs steadily from the hot tap.

On a gas tank, turn the gas control back on only as the label describes. If the pilot went out, relight it by following the instructions on the tank’s label, and stop if it won’t stay lit. Our pilot light guide explains why that can happen.

When to stop and call a technician

Stopping partway is better than forcing a flush that isn’t working. Sediment can jam a drain valve, and old valves can crack under a hose. If any of the following happens, close the cold water valve on top, leave the gas or power off and call.

  • The drain valve is brittle, cracks or leaks when you touch it.
  • The drain valve won’t close fully after draining.
  • Water runs out slowly, stops or only rust-coloured sludge comes out.
  • Water keeps coming from the relief valve discharge pipe.
  • You’re unsure about any step.

If you smell gas at any point, don’t stop to close valves: leave the house without touching switches and call Enbridge Gas at 1-866-763-5427 from outside.

How to flush a water heater: what not to do

Learning how to flush a water heater should be simple, but a few shortcuts turn a routine job into a repair call. The cautions below cover the ones to avoid, and they’re worth reading before you reach for the hose.

  • Don’t pour vinegar, descaler or any chemical into the tank or a gas appliance.
  • Don’t remove an anode rod, which should be left to a technician.
  • Don’t touch the relief valve beyond what the manual asks you to do.
  • Don’t open burner or electrical covers.
  • Don’t put the power back on to an electric tank until it’s full.

Flushing for noise, short supply and smells

A flush often helps when a tank is noisy, runs out fast or gives off a smell. For popping and rumbling, see water heater making noise. For a smell, it’s one step of several, and the anode rod and bacteria may need a technician to fix.

Gas, carbon monoxide and scald safety while flushing

Water in a tank can be hot enough to scald long after the heat is off, so let it cool, and keep the hose away from people and pets. Should you catch a gas smell mid-job, drop everything and leave, avoid switches and phones indoors, and call Enbridge Gas at 1-866-763-5427 from outside.

Ontario requires carbon monoxide alarms next to each sleeping area and, since January 1, 2026, on every storey of homes with a fuel-burning appliance, a fireplace or an attached garage, so check that yours work before any job near a gas tank.

  • Carbon monoxide alarm going off while you work: stop, send everyone and the pets outdoors and call 911.
  • Keep children away from the drain hose, since the water can be far hotter than the usual tap setting of about 49°C.

Enbridge’s natural gas safety (opens in a new tab) page lists what to do if you suspect a leak.

What a technician does that a homeowner flush can’t

A TSSA-certified gas technician can flush a tank, but also checks the anode rod, the drain valve, the relief valve and the venting at the same visit. Older tanks with stubborn sediment may need a deeper clean, or a new drain valve fitted first.

Any extra work, such as a new drain valve, is quoted at a flat-rate price you approve first, and our written workmanship warranty covers repairs. See our water heater installation page if the tank is near the end of its life.

Making a flush part of the routine

A flush each year, along with a look at the tank and its venting, keeps most tanks quieter and longer-lived. Our maintenance plan gives you two tune-ups yearly, and a technician can include the water heater when they visit.

FAQ

How to flush a water heater: common questions

How do I flush a water heater safely?

Set the gas control to off or switch off the power, let the tank cool, close the cold water valve on top, then connect a hose from the drain valve to a floor drain. Open a hot tap, drain the tank, close the valve and refill before restarting. Stop if the drain valve is brittle or won’t close.

How often should I flush my water heater?

Many manuals suggest about once a year, and tanks in hard water may need it more often. Check your manual for the interval it gives. A tank that has never been flushed and is many years old is better left to a technician, because disturbed sediment can jam the drain valve.

Do I have to turn off the gas or power before flushing?

Yes. Flush only with the gas control set to off or the power switched off. An electric element heating without water burns out quickly, and a gas burner firing on a low tank can damage it. Keep the heat off until the tank is full again.

What if the drain valve won’t close after flushing?

Stop and call. Sediment or an old valve can stop it sealing. Close the cold water valve on top so the tank stops refilling, leave the gas or power off, and let a technician replace the drain valve. Don’t keep working it, which can make the leak worse.

Why does only rusty or sandy water come out?

That’s sediment and corrosion from the tank’s bottom, which is what the flush is for. A little is normal. If the water stays rust-coloured, or little water comes out, the sediment may be heavy or the valve partly blocked, and a technician should take over.

Can I flush a tankless water heater the same way?

No. A tankless unit has no large tank of sediment. It builds scale inside its heat exchanger and is cleaned by circulating a descaling solution through it, following the maker’s instructions. Our tankless descaling guide explains the process and when to book a service.

Will flushing fix a water heater that rumbles?

Often it helps, because the rumble comes from sediment. If the noise returns quickly or remains after a flush, the sediment may have hardened or the tank may be near the end of its life. A technician can check and tell you which.

Who can flush a water heater in the GTA?

For a flush that’s gone wrong, or a tank that needs more than a flush, our TSSA-certified gas technicians cover the whole GTA, including Markham, Richmond Hill, Vaughan, North York, Toronto, Mississauga and Oakville. All major brands are serviced, and a flat-rate price is agreed before work starts.

Book a visit

Due for a tune-up? We’ll call you back to book.

Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.

(647) 692-0819

Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies

Request a technician

Tell us what’s going on. We’ll call to confirm a time.

What do you need?
How soon? Optional
Add an email or detailsOptional

Or call (647) 692-0819Used only to book your visit. Privacy