
Heat pump emergency heat is a thermostat setting that heats the house with the backup source and leaves the heat pump itself off. It keeps a home warm when the heat pump has failed or iced over, but it costs more to run, so it is a short-term fix. Here is what it does, when to use it, and when to call for heat pump repair.
Key takeaways
- Emergency heat uses the backup source only, such as electric strips or a gas furnace.
- Use it when the heat pump has stopped heating, not just because it’s cold out.
- Aux heat comes on by itself to help. Emergency heat is something you choose.
- Running it for long costs more than normal heat pump heating.
- If your system has no emergency setting, call for service when heat fades.
Last updated . Written and reviewed by the Assurance HVAC Heating & Cooling service team.
On this page
- What heat pump emergency heat is
- Emergency heat vs aux heat: the difference
- When to use heat pump emergency heat
- When not to switch to emergency heat
- How to switch to emergency heat on the thermostat
- Why heat pump emergency heat costs more
- Systems with no emergency heat setting
- Heat pump emergency heat and safety with gas backup
- Quick checks before relying on emergency heat
- What a technician checks when you’re on emergency heat
- Keeping emergency heat for emergencies only
- Heat pump emergency heat: common questions
What heat pump emergency heat is
Heat pump emergency heat is a setting that bypasses the heat pump and heats with the backup source alone. On many ducted systems the backup is a set of electric heating elements, sometimes called heat strips, in the air handler. In a dual-fuel system it can be the gas furnace instead.
The setting is a manual switch on the thermostat. Once it’s on, the outdoor unit stays off and the backup does all the work until you switch back to Heat.
Emergency heat vs aux heat: the difference
Aux heat and emergency heat both use the backup, but only one is automatic. Aux heat comes on by itself when the heat pump needs help, for example in a cold snap, during defrost, or when the house is far from the setpoint. Emergency heat is chosen by you and shuts the heat pump out completely.
| Aux heat | Emergency heat | |
|---|---|---|
| Who starts it | The thermostat, automatically | You, by changing the setting |
| Heat pump running | Yes, helped by the backup | No, the backup works alone |
| Typical use | Cold weather, defrost, big temperature gaps | A failed or iced-over heat pump |
| Running cost | Higher than heat pump alone | Usually highest with electric strips, because the pump is off |
| Thermostat light | Aux or Heat Strips on | Emergency or Em Heat on |
When to use heat pump emergency heat
Use heat pump emergency heat only when the heat pump itself isn’t working. That means the outdoor unit is dead, iced over solid, making alarming noises or blowing cold air for a long stretch, and the house is cooling. Switching on the setting keeps the home warm until a technician arrives.
- The outdoor unit is iced over and not clearing after you have removed the snow
- The outdoor fan or compressor has stopped and the breaker is fine
- Air at the vents is cold for a long time in Heat mode
- The house is dropping below the setpoint and you are waiting for a technician
- A loud grinding, banging or buzzing from the outdoor unit
When not to switch to emergency heat
Emergency heat is not a way to save the heat pump on a cold day, and it isn’t needed just because the temperature dropped. Aux heat already covers cold snaps automatically. Switching to emergency heat for convenience means paying more to heat with a source that works harder than the heat pump.
Also skip it during an ordinary defrost cycle. The thermostat will cover the few minutes of cool air on its own, and the heat pump goes back to work afterwards.
How to switch to emergency heat on the thermostat
The steps depend on your thermostat, so check its manual. On most, you choose the system mode and pick Emergency or Em Heat from the list, and a light or label confirms it. On a smart thermostat, it may sit in a menu under Equipment or System.
- Set the mode to Emergency Heat or Em Heat, then raise the setpoint above room temperature.
- Check that warm air starts to come from the vents after a few minutes.
- Look at the thermostat for an Emergency or Em Heat light.
- Switch back to Heat once the repair is done, or if the problem clears.
- If there is no such mode, call for service when the heat fades.
Why heat pump emergency heat costs more
A heat pump moves heat rather than making it, so it can deliver more heat than the electricity it uses. Electric backup strips do the opposite: they turn each unit of electricity into one unit of heat. That’s why a few days on emergency heat can lift a hydro bill noticeably compared with normal operation.
A gas furnace backup in a dual-fuel system depends on your gas and electricity rates, so the cost gap varies. Either way, treat emergency heat as a stopgap and book the repair promptly.
Systems with no emergency heat setting
Not every heat pump has emergency heat. Ductless mini-splits usually have no backup source, so there is no setting to switch to, and some ducted systems with a simple thermostat lack it too. If yours has none and the heat pump has stopped, a portable electric heater and a quick call for repair are the practical answers.
Use an electric heater only, by its instructions, plugged into a wall outlet and kept clear of anything that can burn, and never leave it unattended. Never heat the house with a gas oven, a barbecue or a fuel-burning space heater. If the house is getting cold, don’t wait until morning to call.
Heat pump emergency heat and safety with gas backup
If your backup is a gas furnace, the usual gas safety rules apply when it runs in emergency mode. Ontario requires carbon monoxide alarms next to each sleeping area and, since January 1, 2026, on every storey of homes with a fuel-burning appliance, a fireplace or an attached garage, and working alarms matter more when the furnace runs for long hours.
- Gas smell: leave the home without touching switches or phones, then call Enbridge Gas at 1-866-763-5427 from outside.
- CO alarm sounding: get everyone, pets included, outside and call 911.
- Electric strips that smell burnt or trip the breaker: switch to Off and call for service.
The province’s carbon monoxide safety page (opens in a new tab) explains alarm placement and what to do.
Quick checks before relying on emergency heat
A few simple checks sometimes bring the heat pump back, so run through them before settling in on backup heat. Keep to the safe list, and leave the outdoor unit’s panels, wiring and refrigerant lines alone.
- Confirm the thermostat is in Heat mode, with fresh batteries if it takes them.
- Replace a clogged filter and open all registers.
- Clear snow and ice off the outdoor unit by hand, without chipping.
- Reset a tripped breaker once. If it trips again, leave it off.
If the outdoor unit still won’t run, keep emergency heat on and call. Read heat pump frozen for what ice on the unit means.
What a technician checks when you’re on emergency heat
Being on emergency heat means the heat pump has a fault, and the repair visit is about finding it. A technician tests the controls and capacitors, the reversing valve and defrost parts, the fan motor and compressor, and the refrigerant charge, and traces any leak before adding refrigerant.
We repair ducted and ductless systems across the GTA, from heat pump repair in Mississauga to Oakville and Richmond Hill. You approve a flat-rate price before work starts.
Keeping emergency heat for emergencies only
An annual tune-up reduces how often a heat pump leaves you reaching for the setting. A technician checks the defrost controls, the fan and the refrigerant charge, and tests the backup so it works when you need it. Our maintenance plan includes two visits a year.
If your heat pump is around 15 years old and the backup runs a lot, ask about replacement options on our heat pump installation page.
Heat pump emergency heat: common questions
What is emergency heat on a heat pump?
It’s a thermostat setting that turns the heat pump off and heats the house with the backup source alone, such as electric heating elements or a gas furnace. It’s meant for when the heat pump has failed or iced over, and it costs more to run than normal heat pump heating.
Is emergency heat the same as aux heat?
No. Aux heat comes on automatically to help the heat pump in cold weather or during defrost, and the heat pump keeps running. Emergency heat is a setting you choose, and it turns the heat pump off. Many thermostats show a light for each, so check yours to tell which is active.
When should I use emergency heat?
Use it when the heat pump has stopped working or is iced over and the house is getting cold, such as when the outdoor unit is dead, makes loud noises or blows cold air for a long time. Don’t use it just because it’s cold outside, since the system manages cold snaps automatically.
Is it bad to leave my thermostat on emergency heat?
It won’t usually harm the equipment, but it’s expensive. With electric backup, the system makes one unit of heat per unit of electricity, while a heat pump can do far better. Leaving it on all winter by mistake is a common reason for an unexpectedly high hydro bill.
How much does emergency heat cost to run?
It depends on your electricity or gas rates and how long the backup runs, so there’s no single figure. With electric strips it’s noticeably more than normal heat pump heating, because the heat pump is switched out of the picture. Use it only until the repair is done.
My heat pump has no emergency heat setting. What do I do?
Ductless mini-splits and some ducted systems have no backup source, so there’s no setting. If the heat pump stops on a cold night, use a portable electric heater carefully, never a gas oven or fuel-burning heater, and call for repair right away. A technician can also advise whether adding backup heat suits your home.
Does the emergency heat light mean something is broken?
Not necessarily. An Aux light during defrost or a cold spell is normal, because the backup is helping the heat pump. An Em Heat light usually means the emergency setting is on and you’re paying for backup heat alone, so switch back to Heat if the heat pump hasn’t failed. If Aux stays on for hours while the house stays cold, book a service call.
Who repairs a heat pump when it’s stuck on emergency heat?
Assurance HVAC Heating & Cooling repairs heat pumps across Toronto, North York, Richmond Hill, Vaughan, Markham, Mississauga and Oakville. Technicians go out day or night, you approve a flat-rate price before work starts, and repairs carry our written workmanship warranty. All major brands are serviced.
Still no heat? We’ll call you back to book a technician.
Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.
Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies
