---
title: "Water heater pilot light won’t stay lit | Assurance HVAC"
description: "Water heater pilot light going out? Learn the usual causes, how to relight a standing pilot from the tank’s label, and when to call a technician."
canonical: https://assuranceheatingandcoolinghvac.com/guides/water-heater-pilot-light-wont-stay-lit/
last_updated: 2026-11-05
---

Homeowner guides

# Water heater pilot light won’t stay lit

[(647) 692-0819](tel:+16476920819) Open 24/7, day or night

A water heater pilot light that keeps going out leaves you with cold showers and a tank that can’t heat. The cause is often a worn part rather than a dead heater, but it’s a gas problem, so the safe checks are limited. This guide explains why the flame quits, how to relight it by the label, and when to book [water heater repair](https://assuranceheatingandcoolinghvac.com/services/water-heater-repair-toronto/).

[Call (647) 692-0819](tel:+16476920819) Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies

## Key takeaways

- A pilot that lights but won’t stay lit usually points to a worn thermocouple or a venting problem.
- Relight a standing pilot only by following the instructions on the tank’s label, and stop if it fails.
- Never open sealed burner compartments, adjust the gas valve or clean the pilot assembly yourself.
- If you smell gas, leave the house and call Enbridge Gas from outside.
- A TSSA-certified gas technician tests the part and quotes a flat-rate price first.

Last updated November 5, 2026. Written and reviewed by the Assurance HVAC Heating & Cooling service team.

Need a technician?

Flat-rate price before any work starts.
[(647) 692-0819](tel:+16476920819) Request a technician online

**On this page**

- How a water heater pilot light works
- Why a water heater pilot light keeps going out
- A worn thermocouple and why it fails
- Venting, drafts and a pilot flame that blows out
- Dust, lint and a clogged flame arrestor
- How to relight a water heater pilot light safely
- What not to do when the pilot won’t light
- Gas smell and carbon monoxide around a water heater pilot light
- What a technician does for a pilot that won’t stay lit
- Repair or replace when the pilot keeps failing
- Keeping the pilot lit year to year
- Water heater pilot light won’t stay lit: common questions

## How a water heater pilot light works

A standing water heater pilot light is a small, steady flame at the base of a gas tank. It lights the main burner when the tank calls for heat, and it also holds a safety device open. If the flame goes out, that device shuts off the gas so the tank can’t fill the room with fuel.

That safety device is a thermocouple, a thin metal rod sitting in the pilot flame. The heat makes it produce a tiny electric signal that keeps the gas valve open. No flame means no signal, and the gas stops.

## Why a water heater pilot light keeps going out

A pilot that keeps going out almost always has one of a handful of causes. The flame may be weak or off-target, the thermocouple may be worn so it no longer holds the valve open, or air movement near the tank may blow the flame out. A failing gas control valve can also drop out even when the flame looks fine.

Pilot light symptoms, likely causes and who handles them
What you notice | Likely cause | Who fixes it |
Lights while you hold the button, dies when released | Worn or misaligned thermocouple | Technician |
Goes out after hours or days | Draft, venting problem or weak pilot flame | Technician |
Goes out when a dryer or range hood runs | Air pulled through the vent or burner area | Technician |
Yellow, flickering or lazy flame | Dirty pilot assembly or poor combustion air | Technician |
Won’t light at all | No gas, a failed valve or a blocked pilot tube | Technician; check the label first |
Smell of gas | Gas leak | Leave and call Enbridge Gas |

## A worn thermocouple and why it fails

The thermocouple is the part most often behind a water heater pilot light that won’t stay lit. Years of heat cycles weaken it, and soot or corrosion on its tip reduces the signal it makes. When the signal drops too low, the gas valve closes even though the flame is burning.

The classic sign is a pilot that stays lit only while you hold the button down. Replacing a thermocouple is quick for a technician, but it sits right beside the flame and the gas fittings, so it isn’t a homeowner job.

## Venting, drafts and a pilot flame that blows out

A pilot flame is small, so it takes little air movement to disturb it. A partly blocked flue, a bird’s nest in a vent or a backdraft pulling exhaust back down can snuff it out. So can a tight, newer home where a dryer and a range hood compete for air and pull from the water heater’s vent.

Backdrafting is a safety issue, not just a nuisance, because it can push combustion gases into the room. If the pilot goes out on windy days or whenever a fan runs, tell the technician, who checks the draft and the venting.

## Dust, lint and a clogged flame arrestor

Most gas tanks built in roughly the last 20 years are designed to resist igniting flammable vapours, with a flame arrestor screen at the base that stops a flame reaching vapours outside the tank. Dust, pet hair and lint can clog that screen, starving the pilot and burner of air, so the flame struggles and dies.

A technician cleans the screen and the burner properly and checks combustion. That work needs the sealed burner compartment opened, and it’s not something to attempt with a vacuum or a poker. Keep the floor around the tank clear of lint, boxes and anything flammable.

## How to relight a water heater pilot light safely

Relighting a standing pilot is something a homeowner may do, but only by following the instructions printed on the tank’s label. Every model has its own order of steps and its own waiting times, so follow your label word for word, and not a video of another tank.

- Read the label first. If you can’t find it or it isn’t readable, stop and call.
- If you smell gas at any point, stop, leave the house and call Enbridge Gas from outside.
- Follow the label’s steps in the exact order, including the waiting time it asks for.
- Use only the control and the long lighter the label describes.
- If the pilot won’t light, or goes out again when you release the button, stop after one careful try.
- A unit with no standing pilot, or one that lights electronically, isn’t a relight job. Call instead.

A pilot that won’t stay lit after one careful try is telling you a part has failed.

## What not to do when the pilot won’t light

Frustration is the biggest risk when a pilot won’t cooperate. A gas appliance can only be fixed so far with patience, and past that point, shortcuts become dangerous. The list below covers the temptations to resist, however easy they look online.

- Don’t open the sealed burner door or take off covers to reach the pilot.
- Don’t bend, bypass or tape up the thermocouple or any safety device.
- Don’t turn the gas control past what the label says.
- Don’t keep trying and relighting over and over. Gas can collect.
- Don’t pour or spray anything into the burner area.

## Gas smell and carbon monoxide around a water heater pilot light

A gas water heater with a faulty pilot is a gas safety question. Smell gas at any stage and the rule is to leave straight away, with no switches and no phone use indoors, then call Enbridge Gas at 1-866-763-5427 from the yard or street. Don’t go back in until they say it’s safe.

- A carbon monoxide alarm going off means getting the household and pets outdoors first, then calling 911.
- Soot, a yellow flame or scorch marks around the tank are reasons to switch off and call.
- In Ontario, a home with a fuel-burning appliance, a fireplace or an attached garage must have working CO alarms by each sleeping area and on every storey.

Enbridge Gas publishes [natural gas safety](https://www.enbridgegas.com/safety) advice for homeowners.

## What a technician does for a pilot that won’t stay lit

A TSSA-certified gas technician works through the likely causes in order. They check the pilot flame, test the thermocouple’s output, clean the pilot assembly and burner, inspect the flue and venting for draft, and test the gas control valve.

No repair begins until you’ve approved a flat-rate price, and the finished work is covered by our written workmanship warranty. No-hot-water calls are open 24/7, and our [area water heater repair page for Vaughan](https://assuranceheatingandcoolinghvac.com/service-area/vaughan/water-heater-repair/) shows how local service works.

## Repair or replace when the pilot keeps failing

A thermocouple is a small part, so replacing it makes sense on most tanks. The picture changes on an older tank: one past 10 or 12 years, with rust, sediment or a leaking body, is near the end of its life. A tank that needs a new gas control valve as well is often better replaced than repaired.

Our [water heater installation](https://assuranceheatingandcoolinghvac.com/services/water-heater-installation-toronto/) page explains the replacement options, and the [how long do water heaters last](https://assuranceheatingandcoolinghvac.com/guides/how-long-do-water-heaters-last/) guide helps you judge age.

## Keeping the pilot lit year to year

A little attention keeps a pilot happy. Keep the area around the tank clear and free of lint, make sure nothing blocks the vent, and have the tank checked as part of regular service. Our [maintenance plan](https://assuranceheatingandcoolinghvac.com/maintenance-plan/) covers two tune-ups a year, and a technician can look at the venting each visit.

Find these guides useful? Add Assurance HVAC Heating & Cooling as a preferred source, and Google shows our articles more often in your Top Stories when you search.
[Add as a preferred sourceon Google](https://www.google.com/preferences/source?q=assuranceheatingandcoolinghvac.com)

FAQ

## Water heater pilot light won’t stay lit: common questions

**Why won’t my water heater pilot light stay lit?**

The most common reason is a worn thermocouple that no longer produces enough signal to hold the gas valve open. Others are a weak or dirty pilot flame, a draft or blocked vent blowing it out, and a failing gas control valve. If it dies the moment you release the button, expect the thermocouple.

**Is it safe to relight a water heater pilot light myself?**

You may relight a standing pilot by following the instructions on the tank’s label exactly. If you smell gas, stop, leave the house and call Enbridge Gas at 1-866-763-5427 from outside. Stop and call us if you can’t read the label or the flame won’t stay lit after one careful try. Never open the burner compartment or adjust the gas valve beyond the label’s steps.

**How long should I hold the button when relighting a pilot?**

Your tank’s label gives the exact time, so use that rather than a guess. The button is held to let the thermocouple warm and send its signal. If the flame dies as soon as you let go, even after holding as long as the label says, the thermocouple or valve has probably failed.

**Can a water heater pilot light go out from wind?**

Yes, indirectly. Strong wind can push air down the flue, and a dryer or range hood can pull air through the vent, either of which can blow out a small flame. A pilot that goes out only in wind or when fans run points to a draft or venting issue for a technician.

**Does a new water heater still have a pilot light?**

Many still do. Standard gas tanks often use a standing pilot, while power-vent tanks and most tankless units use electronic ignition, which lights the burner on demand with no standing flame. If your tank has a standing pilot, the label shows the relight steps. If it has electronic ignition, a dead burner needs a technician.

**What does a yellow pilot flame mean?**

A healthy pilot flame burns mostly blue. A yellow, flickering or lazy flame suggests poor combustion from a dirty pilot assembly, blocked air or a venting problem, and it can mean carbon monoxide is being produced. Turn the heater off and call a gas technician rather than relighting it.

**How much does it cost to fix a pilot light that won’t stay lit?**

The cost depends on the part that failed and the tank’s age, so it’s not the same for every home. A thermocouple is a modest repair, while a gas control valve costs more. We give you a flat-rate price to approve before any work begins, and you can compare it against replacement.

**Who repairs a water heater pilot light in the GTA?**

Our gas technicians are TSSA-certified and look after gas water heaters in Richmond Hill, Vaughan and Markham, as well as Toronto, North York, Mississauga and Oakville. We work on all major brands and take calls around the clock. Booked visits get a two-hour arrival window and a text when the technician is on the way.

Book a visit

## Still no hot water? We’ll call you back to book a technician.

Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.

[(647) 692-0819](tel:+16476920819)

Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies

For AI agents: [site summary](https://assuranceheatingandcoolinghvac.com/llms.txt), [full text](https://assuranceheatingandcoolinghvac.com/llms-full.txt), [sitemap](https://assuranceheatingandcoolinghvac.com/sitemap.xml).
