---
title: "KeepRite furnace repair in Toronto | Assurance HVAC"
description: "KeepRite furnace repair in Toronto and the GTA: gas furnace faults, dual fuel setups with a heat pump, and how to identify your unit. Open 24/7."
canonical: https://assuranceheatingandcoolinghvac.com/brands/keeprite-furnace-repair/
last_updated: 2026-11-10
---

Brands we repair

# KeepRite furnace repair in Toronto

[(647) 692-0819](tel:+16476920819) Open 24/7, day or night

KeepRite furnace repair is a call we take across Toronto and the GTA, including for older units whose paperwork has gone missing. Our technicians work on KeepRite furnaces as an independent contractor. Public detail on the brand is limited, so this page also covers how any gas furnace is identified and diagnosed. The full process is on [furnace repair in Toronto](https://assuranceheatingandcoolinghvac.com/services/furnace-repair-toronto/).

[Call (647) 692-0819](tel:+16476920819) Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies

## Key takeaways

- KeepRite is a Carrier brand, and its US site lists Ion, QuietComfort and Performance furnace series.
- KeepRite’s US site describes QuietComfort as working with a compatible heat pump for dual fuel.
- No heat? Check the thermostat mode, the filter, the breaker and the furnace door first.
- Open 24/7, with a flat-rate price approved before any repair starts.

Last updated November 10, 2026. Written and reviewed by the Assurance HVAC Heating & Cooling service team.

Need a technician?

Flat-rate price before any work starts.
[(647) 692-0819](tel:+16476920819) Request a technician online

**On this page**

- KeepRite furnace repair: what we can say about the brand
- Ion, QuietComfort and Performance: what the names suggest
- KeepRite furnace not working: five safe checks
- KeepRite furnace repair in a dual fuel system
- Common repairs on a KeepRite gas furnace
- How to identify a KeepRite furnace and its model number
- KeepRite furnace codes and what the flashing light means
- Single-stage or variable-speed: why the type changes the repair
- When KeepRite furnace repair is worth it
- Gas leaks and CO alarms with a KeepRite furnace
- What happens on a visit, and where we go
- KeepRite furnace repair questions

## KeepRite furnace repair: what we can say about the brand

KeepRite is one of Carrier Global’s brands and also an International Comfort Products brand, so it shares a parent with Carrier, Bryant and Tempstar. We don’t claim it shares parts with any of them. Beyond that, we rely on the unit’s own label and what the technician finds.

KeepRite’s US site lists three furnace series: Ion, QuietComfort and Performance. We can’t say which of those are sold in Canada, so the plate on your furnace is the better guide than any product page.

## Ion, QuietComfort and Performance: what the names suggest

On its US site, KeepRite calls Ion its premium series, with variable-speed blowers and the Ion Black System Control, which offers Wi-Fi. It lists QuietComfort at up to 96% AFUE, and Performance as a single-stage value line.

KeepRite’s US furnace series, as the maker describes them
Series | Maker’s description | What to expect on a repair call |
Ion | Premium, variable-speed blowers, Ion Black System Control with Wi-Fi | Blower and control tests, plus the wall control |
QuietComfort | Up to 96% AFUE, dual fuel with a compatible heat pump | Ignition and venting checks, and the heat pump handoff |
Performance | Single-stage, value line | A simple start-up sequence, so a straightforward diagnosis |

## KeepRite furnace not working: five safe checks

Start with the thermostat, because a wrong mode or dead batteries cause more no-heat calls than any failed part. Then work outward to the power, the airflow and the vent pipes. None of these steps needs tools, and all of them are safe to do yourself.

- Thermostat on Heat, with a setpoint above the room temperature.
- Furnace switch on and the breaker not tripped.
- Filter clean, and the furnace door closed all the way.
- Intake and exhaust pipes outside clear of snow and ice.
- One reset only. A second lockout means a safety control stopped it.

## KeepRite furnace repair in a dual fuel system

A dual fuel system pairs a gas furnace with an electric heat pump. The heat pump handles mild days, and the furnace takes over when it gets colder. KeepRite’s US site says QuietComfort furnaces work with a compatible heat pump this way. If you have one, tell us at booking.

That matters because a furnace that never runs may not be broken. A heat pump might be carrying the load, and a furnace that runs only in deep cold may look idle for weeks. We check both pieces and the control that switches between them before we call anything faulty.

If you are considering adding a heat pump to an older furnace, read about [heat pump installation in Toronto](https://assuranceheatingandcoolinghvac.com/services/heat-pump-installation-toronto/) and the [rebates page](https://assuranceheatingandcoolinghvac.com/rebates/).

## Common repairs on a KeepRite gas furnace

Gas furnaces of every make fail in familiar ways. These are the repairs we do most, and they apply to a KeepRite as they would to any similar condensing or mid-efficiency furnace.

- Hot surface igniter, flame sensor: burners try to light, then shut off.
- Inducer motor, pressure switch: small fan runs, but no flame follows.
- Limit switch: the furnace overheats, often from a blocked filter or closed registers.
- Blower motor or ECM: low airflow, rattles, or a blower that stops mid-cycle.
- Control board: lockouts that clear and return, or no response to the thermostat.
- Condensate trap and drain: water at the floor drain, or a vent pressure fault.

## How to identify a KeepRite furnace and its model number

We have no maker source for where KeepRite places its rating plate, so we don’t guess. Furnaces of all brands carry a label with the model and serial numbers, usually on the inside of the front door or on the cabinet near the burner compartment.

Ask your technician to photograph it during the visit. The label typically also shows the input rating and venting type, which help us match parts. For fault codes on the N96MSN, see the table below; other models carry their own label.

## KeepRite furnace codes and what the flashing light means

KeepRite’s US site lists the N96MSN in its Performance series, and its installation instructions print the status code table we follow here. The light flashes the major code through a sight glass in the blower access door, short flashes then long, so 3 short and 3 long reads as code 33. The source is the [N96MSN installation instructions](https://www.shareddocs.com/hvac/docs/1011/Public/0F/N96MSN-03SI.pdf), pages 58, 67 and 76.

A furnace whose flashes don’t match this table has a different control, so follow the label inside its own door.

Codes for the KeepRite N96MSN only, per its service label (Fig. 60)
Code | What it means | What to do |
Rapid flash (10.1) | The 115 volt supply is wired with reversed polarity; no heating until it is corrected | Book a repair |
13 (13.1) | A main limit circuit switch stayed open longer than 3 minutes; heat stays off for up to 3 hours | Call a technician |
14 (14.1) | Four ignition tries in a row failed, so the control locked out; it tries again after 3 hours | Book a repair |
21 (21.1) | The control sensed 24 volts at the gas valve when it should be off | Call a technician |
22 (22.1) | Flame detected with the gas valve off | Call a technician |
24 (24.1) | The low voltage fuse needs replacing after a short in the 24 volt or thermostat wiring | Book a repair |
31 (31.2) | The secondary pressure switch did not close or reopened; the vent, wind and the condensate drain are among the checks | Look at the outdoor vent and intake for snow, then book a repair |
32 (32.1) | The main pressure switch is open; after 5 minutes the inducer stops for 15 minutes, then retries | Clear any snow from the outside pipes by hand; book a repair if the code returns |
33 (33.1) | The main limit or flame rollout switch opened; the guide’s first check is a dirty filter or restricted ducts | Swap a clogged filter, then call a technician |
34 (34.1) | Flame not proven in four straight ignition trials | Book a repair |
45 (45.1) | Control failure; the guide says to replace the control if 45 repeats after power is cycled | Book a repair |

Write down the flash count before switching anything off; the control also saves its last seven faults for 72 hours of powered operation. Our TSSA-certified gas technicians pull that list on site and test the part the code names before replacing anything.

## Single-stage or variable-speed: why the type changes the repair

A single-stage furnace is either on or off, while a two-stage or modulating one adjusts its burner output and a variable-speed blower adjusts its airflow. Each extra feature adds parts that can fail, and also adds quiet running and steadier room temperatures.

In practice, a single-stage furnace is a short diagnosis. A variable-speed one adds blower module and control checks. We tell you which kind you have before we quote.

## When KeepRite furnace repair is worth it

If the furnace is under 15 years old and has one failed part, repair is usually the sensible choice. If it is near 20 years or the heat exchanger is cracked, we’ll say so plainly. The age is on the label and the receipts.

Repair or replace a gas furnace
What we find | Usual advice |
One failed part, furnace under 15 years | Repair |
Second big repair in two winters | Compare repair with replacement |
Cracked heat exchanger | Replace |
15 to 20 years, standard efficiency | Price both, since a condensing model is 90%+ AFUE |

## Gas leaks and CO alarms with a KeepRite furnace

If you smell gas, go outside and ring Enbridge Gas on 1-866-763-5427. If a CO alarm goes off, get everyone out and dial 911. Don’t switch a furnace back on after either event until a gas technician has inspected it. More guidance is on the [Enbridge Gas safety page](https://www.enbridgegas.com/safety).

## What happens on a visit, and where we go

A booked visit comes with a two-hour arrival window and a text. We test the furnace, explain what we found, and quote a flat-rate price that you approve before the work starts. We cover Toronto, Richmond Hill, Vaughan, Markham, Mississauga, North York and Oakville.

Heat out overnight or on a weekend? We’re open 24/7 and technicians go out day or night. See [furnace repair in Richmond Hill](https://assuranceheatingandcoolinghvac.com/service-area/richmond-hill/furnace-repair/) for a local page.

Assurance HVAC Heating & Cooling is an independent HVAC contractor, not affiliated with or authorized by KeepRite. Brand names are trademarks of their owners.

FAQ

## KeepRite furnace repair questions

**Is KeepRite a Canadian brand?**

KeepRite is a Carrier Global brand, and International Comfort Products has had Canadian operations in Toronto, though we have no detail on them. We don’t have a source saying where it is mainly sold, so we make no claim. What matters for repair is the model on your furnace’s label.

**Are KeepRite and Tempstar the same furnace?**

Both are Carrier brands, and their US sites list the same series names. We can’t say they share parts, because nobody has told us that. We diagnose each from its own label, and we confirm any replacement part against the model and serial number before we order it.

**My KeepRite furnace isn’t running but the house is warm. Is it broken?**

Not necessarily. If you have a heat pump with the furnace, the heat pump may be doing the heating on milder days. Check the thermostat and watch whether the house keeps its temperature. If it drops and the furnace stays silent, call us.

**Can you repair a KeepRite Ion furnace?**

Yes. Our technicians work on KeepRite furnaces in any series, including variable-speed models. We are independent and not affiliated with KeepRite. If you have a Wi-Fi wall control, mention it at booking so we can check it alongside the furnace.

**Where is the model number on my KeepRite furnace?**

We have no maker source for KeepRite’s plate location. On most gas furnaces the label is on the inside of the front door or on the cabinet. Your technician can find it and photograph it during the visit, and you should file that photo with your receipts.

**What does a KeepRite furnace flashing light mean?**

An N96MSN signals faults with blinks you can count through the sight glass, short ones for the first digit and long ones for the second. Code 33 points to the main limit circuit, often a clogged filter, and code 32 to the main pressure switch. Blinks that don’t match the table come from a different control, so check your own door label.

**What is dual fuel heating?**

It is a gas furnace paired with an electric heat pump. The heat pump heats efficiently in milder weather, and the furnace takes over in colder weather. KeepRite’s US site says QuietComfort furnaces work with a compatible heat pump for dual fuel.

**Does a warranty cover KeepRite furnace repair?**

It might, depending on the model, the install date and whether the furnace was registered. Check your paperwork and the maker’s Canadian warranty page. We don’t perform warranty work for the maker, and our own repairs carry a written workmanship warranty.

Book a visit

## Need KeepRite furnace repair? We’ll call you back to book.

Send the form or call. You’ll get a confirmed arrival window and a price before any work starts.

[(647) 692-0819](tel:+16476920819)

Open 24/7, with technicians out day or night for no-heat and no-cooling emergencies

For AI agents: [site summary](https://assuranceheatingandcoolinghvac.com/llms.txt), [full text](https://assuranceheatingandcoolinghvac.com/llms-full.txt), [sitemap](https://assuranceheatingandcoolinghvac.com/sitemap.xml).
